9999 ALLISON TRANSMISSION Recalls (4)

Campaign:
91E029000 on 08/12/1991
Component:
Power train:automatic transmission:park/neutral start switch
Manufactured:
03/31/1991 - 05/31/1991
Affected:
3,250
Defect:
An incorrect neutral start switch was installed on some transmissions which allows the truck to be started in a drive position.
Consequence:
If vehicle engine is started with the transmissionselector in a drive position without service or parking brakes applied, thevehicle will move as soon as the engine starts and could result in a vehiclecrash without prior warning.
Correction:
Replace the neutral start switch if determined that the incorrect type of switch was installed.
Notes:
System: automatic transmissions.equipment description: allison automatic transmissions: at500, mt600, v730,ht700, or clbt700 for various heavy duty vehicles.
Campaign:
95E033000 on 08/20/1995
Component:
Power train:automatic transmission
Manufactured:
10/31/1994 - 03/31/1995
Affected:
665
Defect:
The transmission reverse switches can cause the backup lights to be inoperative. this does not conform to the requirements of fmvss no. 108, "lamps, reflective devices, and associated equipment."
Correction:
Dealers will inspect the reverse pressure switch to determine the type of switch installed in the vehicle and replace those switches identified as being suspect.
Notes:
System: powertrain; automatic transmission; fmvss no. 108.equipment description: allison replacement non-electronic automatictransmissions.consequence of noncompliance: the backup lights would be inoperative and alsoit would make the backup audible warning system alarm to be inoperative. thiscan increase the potential for a vehicle accident or personal injury.note: owners who take their vehicles to an authorized dealer on an agreedupon service date and do not receive the free remedy within a reasonabletime, should contact allison transmission at 1-317-242-3554. also contactthe national highway traffic safety administration's auto safety hotline at1-800-424-9393.
Campaign:
00E043000 on 08/06/2000
Component:
Power train:automatic transmission
Manufactured:
02/29/2000 - 04/29/2000
Affected:
640
Defect:
Equipment description: allison transmission 1000 and 2400 series manufactured between march 1 and april 30, 2000. these automatic transmissions can experience park pawl to rear cover interference due to an out of flatness condition.
Consequence:
this could cause non-engagement of the park pawl when the transmission shift selector is moved to the park position. this could result in unintended vehicle movement and a vehicle crash without prior warning.
Correction:
Dealers will remove the transmission from the vehicle, replace the park pawl, and reinstall the transmission in the vehicle.
Notes:
Owner notification began on august 14, 2000.owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact allison transmission at 1-800-252-5283.also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).
Campaign:
02E018000 on 04/02/2002
Component:
Power train:manual transmission:shift pattern indicator
Affected:
28
Defect:
Equipment description: the "check transmission" light in certain allison md world transmissions, a division of the general motors corporation, was incorrectly calibrated into the electronic control unit (ecu). these transmission were installed on certain international ngv 4000 / 7000 series trucks. the "check transmission" light indicates to the driver that the transmission is not fully operational, and that it should be repaired immediately. in those instances that the "check transmission" light would normally be illuminated as a result of a problem that prevents direction changes (such as shift selector malfunction) the driver may not be adequately aware of the problem.
Consequence:
The driver may inadvertently have the vehicle move in a director opposite to his intention which could result in a vehicle crash, possibly resulting in serious injury.
Correction:
Allison will notify its customers and recalibrate the transmission ecu free of charge. owner notification began march 15, 2002. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact allison customer assistance center at 800-524-2303.
Notes:
also, customers can contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

9999 ALLISON TRANSMISSION TSBs (139)

Bulletin:
3TR97
Component:
061100 engine and engine cooling:engine:gasoline
Summary:
Engine surging or engine speed cycling may occur on natural gas powered equipment. *ak
Bulletin:
98500
Component:
101000 power train:clutch assembly
Summary:
Subject on customer satisfaction campaign on c5 clutch friction material. *yc
Bulletin:
6WT98
Component:
116200 electrical system:ignition:module
Summary:
Allison transmission has determined that electrical transient voltage signals present on the vehicle chassis can cause wtec electronic control unit (ecu) diagnostic codes. therefore, a chassis isolation kit has been developed to aid in is
Bulletin:
9WT98
Component:
102000 power train:manual transmission
Summary:
Experiencing a code 54 23 when a closed throttle 2-1 downshift is interrupted before the shift is completed by an increase in throttle percentage and the shift changes to powered downshift. *yc
Bulletin:
12WT98
Component:
103000 power train:automatic transmission
Summary:
Experiencing an intermittent 1-2/2-1 shift cycle while the transmission is in drive and the vehicle is stationary. *tt
Bulletin:
24-TR-98
Component:
103000 power train:automatic transmission
Summary:
Subject on ht / clt 700 modulator body. *tt
Bulletin:
9WT98A
Component:
102000 power train:manual transmission
Summary:
Vehicles with world transmissions controlled bu v7 or v7a software can experience a code 54 23. *tt
Bulletin:
211K2K00
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
This service information letter introduces the release of the 2000 motor home transmission (2000 mh). the new 2000 mh model will be mated only to the cummins isb engine rated at 275 hp and 600 ft-lbs. to accommodate the additional input
Bulletin:
2000C2A
Component:
103000 power train:automatic transmission
Summary:
Allison transmission has decided that some 1000 series and some 2400 series transmission may exhibit a condition in which the park pawl does not engage when the transmission shift selector is moved to the park position. *tt
Bulletin:
81K2K01
Component:
103000 power train:automatic transmission
Summary:
Subject regarding neutral start back up (nsbu) switch damage on 1000 / 2000 / 2400 series transmissions. *tt
Bulletin:
211K2K00A
Component:
103000 power train:automatic transmission
Summary:
Service information on the release of the new 2000 series transmission. *tt
Bulletin:
71K2K01
Component:
103000 power train:automatic transmission
Summary:
This service information letter introduces the 1000 / 2000 / 2400 series retran transmission. *tt
Bulletin:
9TR01
Component:
103000 power train:automatic transmission
Summary:
Subject regarding the release of the new polyester sump filter for all at 500 transmissions with the 5.3 inch deep oil pan. *tt
Bulletin:
17WT98A
Component:
102300 power train:manual transmission:shift pattern indicator
Summary:
Information regarding allison transmission's release of the new pushbutton shift selector for use only with wtec iii electronic controls. *tt
Bulletin:
12TR01
Component:
102000 power train:manual transmission
Summary:
This service information letter provides an update to product improvements made to the m/s 9600 and s 9800 models. *tt
Bulletin:
10WT01
Component:
102000 power train:manual transmission
Summary:
Allison transmission service information regarding cancellation of md pre-block retran center assembly numbers. *tt
Bulletin:
11WT01
Component:
103000 power train:automatic transmission
Summary:
Subject regarding new electronic control units, v9a controls software, and new transmission calibrations for world transmission models. *tt
Bulletin:
18WT01
Component:
102000 power train:manual transmission
Summary:
Subject regarding wtec iii lever shift selector availability and service parts. *slc
Bulletin:
20WT01
Component:
102000 power train:manual transmission
Summary:
Subject regarding filter cover bolt hole repair kit. *slc
Bulletin:
25WT01
Component:
102000 power train:manual transmission
Summary:
Subject regarding hd/b 500/4000mh bearing retainer locknut retention. *tt
Bulletin:
5WT02
Component:
102000 power train:manual transmission
Summary:
Subject regarding changes to wt transmissions using fire truck pump mode (ftpm) function for version 9a software. *tt
Bulletin:
3TR02
Component:
101000 power train:clutch assembly
Summary:
Subject regarding revised intermediate carrier assembly practices for m9600 transmissions with two speed reverse option. *tt
Bulletin:
21K2K02
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Subject regarding new tcm calibration and software. *tt
Bulletin:
10TR99B
Component:
103000 power train:automatic transmission
Summary:
Subject regarding atd factory fill of transynd revised transmission fluid / filter change recommendations for at500, mt600, ht700, md3000, hd4000, b3/4/500, 1000, 2000, 2400, 200mh and t series transmissions. *tt
Bulletin:
1TR02
Component:
102000 power train:manual transmission
Summary:
Subject regarding power takeoff bearing update for all 5/6000 series transmissions. *tt
Bulletin:
700200213301
Component:
102000 power train:manual transmission
Summary:
Subject regarding location of allison diagnostic plug on freedom chassis. nlm
Bulletin:
27WT96B
Component:
100000 power train
Summary:
Correct installation of sealrings when overhauling an allison wt transmission. *tt
Bulletin:
26WT02
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Coating on world transmission control module threaded fasteners. *tt
Bulletin:
27TR02
Component:
102000 power train:manual transmission
Summary:
Lube flow/product improvements. m/s9600, s9800 models. *tt
Bulletin:
32TR02
Component:
100000 power train
Summary:
Release of j-46550 pall transmission cooler kwik-flush cart. *tt
Bulletin:
31TR02
Component:
100000 power train
Summary:
Mt converter pump cover assembly. *tt
Bulletin:
4WT03
Component:
100000 power train
Summary:
New output seal, yoke/flange and slinger configuration. all hd 4000, b500 and t400 series transmissions. *tt
Bulletin:
2008FA-2
Component:
350000 equipment
Summary:
Allison transmission service campaign: see document search button for owner letter. ac current sensor wiring harness replacement installed in dual power inverter modules (dpims) built between 12/22/05 and 3/6/07. have improper shield wire
Bulletin:
2008FA-5
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Allison transmission service campaign: see document search button for owner letter. in some 24 volt 4th gen calibrations the main modulation solenoid may not activate properly at idle; which reduces cooler flow at idle. csc letter was
Bulletin:
2008FA-4
Component:
103000 power train:automatic transmission
Summary:
Allison transmission service campaign: see document search button for owner letter. high voltage interlock loop (hvil) circuit cards for ep 40/50 system, installed in dual power inverter modules (dpim) built between 6/14/05 & 6/20/06 will b
Bulletin:
2008-FA-6
Component:
102000 power train:manual transmission
Summary:
Allison transmission service campaign: see document search button for owner letter. potential concern with shift valve trim springs in dock spotter and transit bus vocations. the 3000 product family, b 300, b 400, b 500 and t models are
Bulletin:
CS-2010FA01
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Allison transmission service campaign: see document search button for owner letter. daimler buses north america (80 tcms installed into orion buses operating at long island transit). the current sense resistor solder joint may crack due t
Bulletin:
FA-2009FA04
Component:
355200 equipment:other:owners/service/other manual
Summary:
Allison transmission service campaign: see document search button for owner letter. the t-10 bearing surface on motor b rotor may not have a flat surface and cause the t-10 bearing to fail. when the t-10 bearing fails, debris can be distr
Bulletin:
IK-1300055
Component:
102000 power train:manual transmission
Summary:
International: due to poor shifting quality, too fast upshifting, there is a problem in software calibrations for transmissions on some trucks. allison gen 4 lct (1000, 2000). no years listed.
Bulletin:
ICI-15-001
Component:
102000 power train:manual transmission
Summary:
Daimler trucks (allison transmission) : information provided regarding incorrect calibration of load base shift scheduling (lbss), causing poor performance on certain truck, during normal driving conditions, and need to be recalibrated.
Bulletin:
IK1300022
Component:
103800 power train:automatic transmission:park/neutral start switch
Summary:
Iknowledge: all hpv models with allison transmissions and the auto neutral feature may not shift back into gear once the parking brake is released. *ta
Bulletin:
HD-4560
Component:
103700 power train:automatic transmission:torque converter
Summary:
Valley truck: repair procedures provided due to layers of paint on torque converter cover causing changes between adapter ring and torque converter cover of transmissions gear adapter bolts to break. model oshkosh s series. no years liste
Bulletin:
2012FA03
Component:
102000 power train:manual transmission
Summary:
Allison transmission 'this tsb contains an owners notification letter. select document search button below. at no cost to customers, the dual power inverter modules will be removed and replace. *ma updated 01/06/2016. *ma updated 02/02/20
Bulletin:
FA-2014FA01
Component:
103000 power train:automatic transmission
Summary:
Allison transmission: on certain buses, the transmission control module (tcm) calibrations would need to be reprogram due to auto neutral function being active when gear indicates 1st range and speed of engine is elevated. model 2013-14 a
Bulletin:
FA-2014FA03
Component:
103000 power train:automatic transmission
Summary:
Allison transmission: tsb contains an owner's notification letter. select document search button below. water used to verify sealing integrity, had inadvertently entered the transmission fluid and the fluid is detrimental to durability a
Bulletin:
FA-2014FA08
Component:
103000 power train:automatic transmission
Summary:
Allison transmission: transmission control module (tcm), in some trucks, with torque converter lockup, will have premature c4 clutch pack wear and will need to have new calibrations installed to prevent torque converter lockup in the 1st r
Bulletin:
FA-2014FA09
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Allison transmission: some trucks are experiencing symptoms that causes failure to the transmission control module (tcm) such as no forward ranges, will not program or flash, harsh or erratic shifting, will not start, stuck in range, have
Bulletin:
FA-2014FA12
Component:
060000 engine (pws)
Summary:
Allison transmission: accelerate torsional fatigue damage to drive unit input shaft caused by engine rpm dwelling at or near 280 to 560 rpm can be reduced by new developed software for drive unit exposure to excessive engine. *p
Bulletin:
TT-7674EN
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Allison transmission: due to chassis wiring harness, on some coaches, the engine throttle has become unresponsive and need to install retrofit a neutral start circuit installation to chassis wiring harness. *pe
Bulletin:
TT-7484-EN
Component:
103000 power train:automatic transmission
Summary:
Allison transmission: on some trucks, the push button shift selector (pbss) skips oil level reading and goes directly to prognostics and could be missing wire 116 on bulkhead other side. models t680, t880, 579, 567. *pe updated 2
Bulletin:
TT-7539EN
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Allison transmission: on some trucks chassis, the calibration setting for 5th generation controls load based shift scheduling (lbss) is incorrect and causes poor driving performance. *pe
Bulletin:
TT-7491EN
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Allison transmission (peterbilt): due to windshield wiper linkage or unsecured transmission control module (tcm), the transmission harness is damaged and diagnostic trouble codes (dtc) may be due to rainy or wet weather conditions and is
Bulletin:
SIL-4-EP-15
Component:
350000 equipment
Summary:
Allison transmission: procedural information on availability and replacement of passive discharge resistor and related components inside dual power inverter module 2 (dpim2). *pe
Bulletin:
TT-7693EN
Component:
350000 equipment
Summary:
Allison transmission: the c3/c4 bonded piston failed due to an intrusion of water or coolant into transmission fluid. *pe
Bulletin:
SB-2015FA04
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Allison transmission: bulletin on authorization of new a65 tcm calibration installation at no charge. new software update (d151). *cn
Bulletin:
SB-TT7718EN
Component:
103000 power train:automatic transmission
Summary:
Allison transmission: while accompanied by a p0883 tcm power input signal high code, the transmission may shift into neutral while driving. *cn updated 3/17/16 *cn
Bulletin:
SIL 11-1K2K-16
Component:
103000 power train:automatic transmission
Summary:
Summary to be provided on a future date.
Bulletin:
92717
Component:
103000 power train:automatic transmission
Summary:
Summary to be provided on a future date.
Bulletin:
97101
Component:
060000 engine (pws)
Summary:
Summary to be provided on a future date.
Bulletin:
SB-2012-FA-03-D
Component:
350000 equipment
Summary:
Summary to be provided on a future date.
Bulletin:
WA7742EN
Component:
118000 electrical system: software
Summary:
Notification of design change for the 12v and 24v vehicle interface modules (vim) effective q4 2016, allison transmission has modified the 12v and 24v vehicle interface modules (vim) to improve performance and enhance long-term durability.
Bulletin:
SIL 10EP16
Component:
063000 engine and engine cooling:exhaust system
Summary:
Exhaust backfill spring color code the exhaust backfill spring and trim valve spring can be incorrectly mixed during assembly. if the trim valve spring is used in place of the exhaust backfill spring, exhaust backfill pressure will run h
Bulletin:
SIL 06WT16
Component:
355200 equipment:other:owners/service/other manual
Summary:
Torque converter lockup backing plate bolt torque increase for 3000 product family the allison transmission, inc. 3000 product family transmission service manual (sm4013) has increased the torque specification for the torque converter l
Bulletin:
SIL 3EP16
Component:
350000 equipment
Summary:
Replacing the ac busbar assembly and ac terminal block inside the dual power inverter module 2 (dpim2
Bulletin:
SIL 5-EP-16
Component:
350000 equipment
Summary:
Replacing the dc busbar assembly and dc terminal block inside the dual power inverter module 2 (dpim2
Bulletin:
SIL 10-EP16
Component:
103000 power train:automatic transmission
Summary:
The color of the exhaust backfill spring (p/n 29538831) is being changed to orange in order to distinguish it from similar springs used in the h 40/50 ep assembly plant. the spring part number does not change and is fully interchangeable
Bulletin:
SIL 9-EP-16REVB
Component:
100000 power train
Summary:
Announces third generation energy storage system (ess) for the h 40/50 ep products and steps to be taken when a first or second generation ess is replaced with the new third generation.
Bulletin:
SIL 9-EP-16REVA
Component:
100000 power train
Summary:
Announces third generation energy storage system (ess) for the h 40/50 ep products and steps to be taken when a first or second generation ess is replaced with the new third generation.
Bulletin:
SIL 24-WT-16EN
Component:
100000 power train
Summary:
Service information concerning torque-converter-turbine assembly that explains checks to determine if the turbine assembly, hook seal ring, or cover bushing need replacement.
Bulletin:
2015FA11
Component:
100000 power train
Summary:
Neutral at stop (nas) feature enable
Bulletin:
2015FA12
Component:
100000 power train
Summary:
Customer satisfaction field action 2015fa12 -- recalibration for code setting mil lamp during shutdown on hd obd compliant buses
Bulletin:
SIL 01-TR-16EN
Component:
100000 power train
Summary:
Re-calibrating my 2016 vehicles with tcm can1 network speed set to 500 kbps baud rate
Bulletin:
SIL 8-TC10-16
Component:
100000 power train
Summary:
Tc10 hardware modification - a65 tcms, rear covers, and interchangeability
Bulletin:
SIL 09-EP-16
Component:
100000 power train
Summary:
Energy storage system 3 (ess 3) release notification
Bulletin:
2016FA02
Component:
100000 power train
Summary:
Allison transmission and navistar jointly identified a potential quality issue related to adaption hardware. damage to the adaption hardware can develop and lead to failure of the flexplate.
Bulletin:
33-TR-16
Component:
100000 power train
Summary:
Two-part announcement regarding the release of enhancements made to the a61, a62, a63, and a65 5th generation controls tcms and the release of additional 5th generation controls for chassis-mount tcm types called a6a, a6b, and a6c.
Bulletin:
SIL 1-EP-15REVB
Component:
100000 power train
Summary:
Service letter announcing the availability of kits to replace components of the dual power inverter module 2 (dpim2) and eliminating the need to replace the entire dpim2. the announcement includes servicing instructions.
Bulletin:
SIL 9-EP-16REVC
Component:
100000 power train
Summary:
Announces the third generation energy storage system (ess 3), describes the differences between the ess 2 and ess 3, and provides details on new service parts and procedures.
Bulletin:
SIL 34-EP-16EN
Component:
103000 power train:automatic transmission
Summary:
Service letter announcing the availability of service parts to replace the ac choke and o-ring mounted on the dual power inverter module 2 (dpim 2) and service instructions.
Bulletin:
TT7880EN
Component:
100000 power train
Summary:
Installation issue could lead to prolonged contact of air lines with the tcm or transmission wiring harness and vehicles could experience unexpected dtc codes.
Bulletin:
TT7876EN
Component:
100000 power train
Summary:
Field action to update software to ameliorate improper starter engagement and reengagement that can result from rapid key cycle by the operator.
Bulletin:
SIL-35-EP-16
Component:
100000 power train
Summary:
Bulletin announcing the availability of a signal-interface card and encoder card for the inverter for servicing the dpim2. the bulletin also includes service instructions.
Bulletin:
SIL 9-EP-16REVD
Component:
100000 power train
Summary:
Announces the third generation energy storage system (ess 3), describes the differences between the ess 2 and ess 3, and provides details on new service parts and procedures.
Bulletin:
SIL 5-EP-16 REVA
Component:
100000 power train
Summary:
Announces availability of the dc busbar, dc terminal block, hvil support and related components and service instructions to allow repairs to the dpim
Bulletin:
WATCH 512 REV A
Component:
100000 power train
Summary:
Announces the release of software features and enhancements for 5th generation controls.
Bulletin:
WATCH 501 REV D
Component:
100000 power train
Summary:
Announces the release of software features and enhancements for 5th generation controls.
Bulletin:
SIL5-EP-16ENREVB
Component:
100000 power train
Summary:
Announces availability of the dc busbar, dc terminal block, hvil support and related components and service instructions to allow repairs to the dual power inverter module 2 (dpim).
Bulletin:
SIL4-EP-15ENREVB
Component:
100000 power train
Summary:
Announces the availability of the passive discharge resistor as a service part. the communications also contains instructions for replacing the passive discharge resistor assembly inside the dual power inverter module 2 (dpim2).
Bulletin:
SIL 8-TC10-16 RE
Component:
103100 power train:automatic transmission:control module (tcm, pcm)
Summary:
Highlights how changes to tcm and rear cover modifications can affect interchangeability of these components when repairing the transmission.
Bulletin:
2016FA02 Rev B
Component:
060000 engine and engine cooling
Summary:
Allison transmission and navistar jointly identified a potential quality issue related to adaption hardware. damage to the adaption hardware can develop and lead to failure of the flexplate.
Bulletin:
SIL 15-WT-01 Rev
Component:
354000 equipment:mechanical
Summary:
Announces product improvement that decreases the clearance between the planetary spindle and the spindle retaining ring and increased hardness in the spindle retainer. also details dimensions and interchageability of part numbers.
Bulletin:
SIL 4-WT-17EN
Component:
100000 power train
Summary:
Announces new transmission breather using an outer hex design and details for servicing the new design.
Bulletin:
TT7997EN
Component:
100000 power train
Summary:
Service tip instructing service channel to inspect the o-ring of the ps1 and ps2 assembly during disassembly of the part to ensure the servicer did not damage the part during servicing.
Bulletin:
SIL 10-TR-99EN R
Component:
100000 power train
Summary:
Details transmission fluid types and service intervals.
Bulletin:
SIL 7-WT-96 Rev
Component:
100000 power train
Summary:
Announces new external accumulator assemblies for transmissions with a retarder and how to identify the differences in the parts.
Bulletin:
17-TPPL-16
Component:
100000 power train
Summary:
Requests the return of certain wtec iii controls due to non-communication.
Bulletin:
SIL 1-EP-15 Rev
Component:
100000 hybrid powertrain: inverter
Summary:
Announces the availability of skim module and gate drive card service kit and the procedures for replacing these parts.
Bulletin:
SIL 22-EP-17
Component:
100000 power train
Summary:
Announces release of 5th generation control and software for hybrid-transmission product line and tools need for servicing
Bulletin:
TT7994 Rev A
Component:
100000 power train
Summary:
Provides servicing tip for dtc p2789 in ic bus and software reflash instructions
Bulletin:
SIL 26-TR-17
Component:
100000 power train
Summary:
Announces discontinuation of tone wheel part number with a new design and explains interchangeability during servicing
Bulletin:
SIL 28-TC10-17
Component:
100000 power train
Summary:
Announces changes to the gear tooth geometry and interchangeability or components when repairing the tc10 transmission
Bulletin:
2015FA05-ES Rev
Component:
100000 power train
Summary:
Spanish-language version of field action that announces special coverage for a bolt may impact the torque converter turbine and backing plate, resulting in internal debris
Bulletin:
2015FA06-ES Rev
Component:
100000 power train
Summary:
Spanish-language version of customer service campaign related to a bolt may impact the torque converter turbine and backing plate, resulting in internal debris
Bulletin:
SIL 18-WT-17 Rev
Component:
100000 power train
Summary:
Discusses two engine mounting adaption configurations for 4000 series transmissions with navistar n13 engines
Bulletin:
TT8115
Component:
100000 power train
Summary:
Announces field study of output bearings
Bulletin:
SIL 32-WT-17
Component:
100000 power train
Summary:
Announces release of 5th generation software and diagnostic trouble codes
Bulletin:
SIL 07-EP-15 Rev
Component:
355200 equipment:other:owners/service/other manual
Summary:
Announces certplus parts for use in states adopting california air resource board certification requirements
Bulletin:
SIL 17-EP-07 Rev
Component:
060000 engine (pws)
Summary:
Provides servicing information for diagnosing engine low power complaints in conjunction with dtcs
Bulletin:
SIL 18-WT-14 Rev
Component:
060000 engine and engine cooling
Summary:
Announces release of and part numbers for revised oil cooler parts and service information related to the parts
Bulletin:
SIL 02-WT-18
Component:
350000 equipment
Summary:
Announces replacement temperature sensor and its interchangeability with the former sensor
Bulletin:
IS 364
Component:
355200 equipment:other:owners/service/other manual
Summary:
Announces changes to fluid change procedures
Bulletin:
ST1707 Rev E
Component:
355200 equipment:other:owners/service/other manual
Summary:
Troubleshooting guide for low power complaints in conjunction with certain dtcs
Bulletin:
SIL 10-TR-86EN R
Component:
355200 equipment:other:owners/service/other manual
Summary:
Provides technical information regarding driveline components, including inspection processes
Bulletin:
IS 356
Component:
355200 equipment:other:owners/service/other manual
Summary:
Instruction sheet related to servicing neutral at stop low gain valve body
Bulletin:
SIL 06-WT-18
Component:
101000 power train:clutch assembly
Summary:
The control in software update reduced clutch pressures under certain circumstances
Bulletin:
18-TPPL-10
Component:
100000 power train
Summary:
Announce new part numbers for maintenance filter kits
Bulletin:
SIL 04-TR-18EN
Component:
118000 electrical system: software
Summary:
Announces restrictions on calibration settings for new software
Bulletin:
SIL 10-TC10-18
Component:
114000 electrical system:wiring
Summary:
Announces minor visual alteration to the speed sensor connector in the internal wiring harness
Bulletin:
SIL 08-TR-18
Component:
118000 electrical system: software
Summary:
Announces limits for disabling or modifying some custom features in new software
Bulletin:
TT8144EN
Component:
160000 structure
Summary:
Announces compatibility of aluminum main valve body in 3000 and 4000 series transmissions
Bulletin:
SIL 07-TR-18
Component:
118000 electrical system: software
Summary:
Announces calibration settings for neutral at stop feature with new software
Bulletin:
IS 358
Component:
103000 power train:automatic transmission
Summary:
Instructions related for two channel plate gaskets in a seal and gasket kit
Bulletin:
IS 359
Component:
103000 power train:automatic transmission
Summary:
Instructions related to for two channel plate gaskets in a seal and gasket kit
Bulletin:
IS 360
Component:
103000 power train:automatic transmission
Summary:
Instructions related for two channel plate gaskets in a seal and gasket kit
Bulletin:
IS 361
Component:
103000 power train:automatic transmission
Summary:
Instructions related to for two channel plate gaskets in a seal and gasket kit
Bulletin:
SIL 18-TC10-18
Component:
350000 equipment
Summary:
Highlights the release of a new shift valve body separator plate with information on serviceability and interchangeability
Bulletin:
10-WT-00EN Rev A
Component:
103000 power train:automatic transmission
Summary:
Explains redesign of planetary spindles and interchangeability
Bulletin:
2018FA07EN
Component:
100000 power train
Summary:
Announces customer service campaign related to transmission switch issue
Bulletin:
TT7539EN Rev B
Component:
350000 equipment
Summary:
Announces calibration problem from freightliner custom chassis corporation
Bulletin:
TT8025EN Rev A
Component:
350000 equipment
Summary:
Informs service channel that it will support freightliner custom chassis corporation field action related to engine retarder.
Bulletin:
TT8045EN Rev A
Component:
100000 power train
Summary:
Service tip regarding preselect downshift that is being addressed by freightliner custom chassis corporation
Bulletin:
SIL 24-WT-18 EN
Component:
160000 structure
Summary:
Announces omission of trim hole
Bulletin:
SIL 25-1K2K-18
Component:
100000 power train
Summary:
Offers troubleshooting for complaints of harsh shifts and dtc code for clutch adaptive learning at limit
Bulletin:
SIL 14-TR-18EN
Component:
100000 power train
Summary:
Announces and describes new and updated diagnostic trouble codes (dtc) for 5th generation controls.
Bulletin:
SIL 20-WT-18EN
Component:
100000 power train
Summary:
Announces change in color of latch-valve spring that are interchangeable with the prior version
Bulletin:
SIL 22-EP-16 Rev
Component:
100000 power train
Summary:
Provides information related to replacing current sensors inside the dual power inverter module 2 (dpim2)
Bulletin:
SIL 23-TR-18EN
Component:
060000 engine and engine cooling
Summary:
Announces updated design of turbine shaft seal ring
Bulletin:
IS 278
Component:
100000 power train
Summary:
Instructions for identify the correct seal ring when overhauling transmissions
Bulletin:
2015FA06 Rev B
Component:
103700 power train:automatic transmission:torque converter
Summary:
Announces field action regarding the torque converter's backing plate bolt

Home | Privacy