2012 HINO NE8J Recalls (7)

Campaign:: 11V320000 on 06/12/2011
Component:: Suspension:front:wheel bearing
Affected:: 237
Defect:: Hino is recalling certain model year 2011 ne8j vehicles. the front axle outer wheel bearing cone rollers may not have been properly heat treated. the suspect bearing cones have the date code "zj" on the major face of the inner bearing race just following the "canada" stamp.
Consequence:: Without heat treating, a bearing may suffer pre-mature failure which may result in a fire at the wheel or wheel separation that could lead to a crash.
Correction:: Hino will notify owners and repair the vehicles free of charge. the safety recall began on april 19, 2012. owners may contact hino motors at 1-248-699-9330.
Notes:: Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .
Campaign:: 11V537000 on 11/08/2011
Component:: Power train:axle assembly
Manufactured:: 07/24/2011 - 09/15/2011
Affected:: 312
Defect:: Hino is recalling certain model 2012 nd8j, ne8j, nj8j, and nv8j commercial trucks manufactured from july 25, 2011, through september 16, 2011. during assembly, the wheel-end retainer on the front or rear axle may have been installed incorrectly.
Consequence:: The wheel-hub and axle shaft can separate from the vehicle, possibly resulting in a crash.
Correction:: Hino will notify owners, and dealers will inspect the front axle assemblies and, if the axle is found to be incorrectly assembled, dealers will replace the wheel end retaining hardware free of charge. the safety recall began on april 19, 2012. owners may contact hino at 1-248-699-9390.
Notes:: Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .
Campaign:: 11V549000 on 11/16/2011
Component:: Steering
Manufactured:: 02/15/2011 - 03/02/2011
Affected:: 62
Defect:: Hino motors is recalling certain model year 2011-2012 ne8j trucks. during the assembly process, the steering attachment bolts may have been insufficiently torqued.
Consequence:: Insufficient torque of the steering arm bolts may result in bolt fatigue and fracture and/or arm separation, thereby potentially resulting in loss of steering control, increasing the risk of a crash.
Correction:: Hino will notify owners, and dealers will repair or replace the steering arm bolts free of charge. the safety recall began on april 19, 2012. owners may contact hino at 1-248-699-9390.
Notes:: Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .
Campaign:: 12V555000 on 12/03/2012
Component:: Electrical system:battery:cables
Manufactured:: 08/17/2003 - 11/15/2011
Affected:: 35,142
Defect:: Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:: If the b+ circuit shorts to ground, it may lead to a fire.
Correction:: Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:: Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:: 12V555000 on 12/03/2012
Component:: Electrical system:wiring
Manufactured:: 08/17/2003 - 11/15/2011
Affected:: 35,142
Defect:: Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:: If the b+ circuit shorts to ground, it may lead to a fire.
Correction:: Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:: Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:: 14V791000 on 12/14/2014
Component:: Parking brake
Manufactured:: 08/25/2003 - 05/13/2014
Affected:: 8,140
Defect:: Hino motor sales u.s.a., inc. (hino) is recalling certain model year 2005-2015 hino nd8j, ne8j, and nf8j trucks manufactured august 26, 2003, to may 14, 2014. in the affected vehicles, components of the parking brake handle assembly may wear, resulting in either the parking brake unexpectedly releasing when engaged or preventing the parking brake from fully engaging.
Consequence:: Either parking brake condition may result in the vehicle rolling unexpectedly, increasing the risk of a crash.
Correction:: Hino will notify owners, and dealers will install a new parking brake lever that contains a two-way damper and a roller at the cable joining pin, free of charge. the recall began february 2, 2015. owners may contact hino customer service at 1-248-699-9330. hino's number for this recall is a9970. note: this recall supersedes 13v-614.
Notes:: Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:: 17V607000 on 09/28/2017
Component:: Engine and engine cooling:engine:diesel
Manufactured:: 02/03/2010 - 01/06/2011
Affected:: 3,224
Defect:: Hino motor sales u.s.a., inc. (hino) is recalling certain 2011-2012 ne8j, nj8j, and nv8j trucks. the engines have a wrist pin bushings in the connecting rods that may shift and cause excessive cylinder wear.
Consequence:: Excessive wear of the cylinders can result in engine failure, increasing the risk of a crash.
Correction:: Hino will notify owners, and dealers will inspect and, as necessary, replace the connecting rods. interim notices informing owners of the safety risk were mailed november 27, 2017. the recall began on march 19, 2018. owners may contact hino customer service at 1-248-699-9300. hino's number for this recall is aa860.
Notes:: Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.

2012 HINO NE8J TSBs (39)

Bulletin:: RCB-002-13
Component:: 118000 electrical system: software
Summary:: Hino trucks: malfunction indicator lamp (mil) may be illuminating. vehicle may also experience reduced power. performing a software enhancement should correct this problem. *kb
Bulletin:: RCB-008-12
Component:: 118000 electrical system: software
Summary:: Hino trucks: malfunction indicator lamp (mil) possibly illuminating during cold temperatures. software update for the dosing control unit (dcu) could solve this problem. *kb
Bulletin:: RCB-009-12
Component:: 118000 electrical system: software
Summary:: Hino: software update for burner control unit (bcu). ignition of the burner system may perform improperly and cause a mil light to illuminate in the instrument cluster. *kb
Bulletin:: RCB-001-13
Component:: 061200 engine and engine cooling:engine:diesel
Summary:: Hino: soot accumulates on the igniter. burner ignition could perform improperly. replacement of the diesel particulate regeneration (dpr) igniter plugs. *kb
Bulletin:: 167-P1602-12
Component:: 060000 engine (pws)
Summary:: 13-008 injection pump drive case. please note the following part number changes to the injection pump bearing case. not replacing the correct replacement parts will result in major engine damage. the hino ordering system has been modified
Bulletin:: 167-B0501-12
Component:: 060000 engine (pws)
Summary:: 05 - 011 corrections to workshop manuals for j08 engines. the standard gap between ends of the second piston ring and the oil ring.
Bulletin:: 167-B0502-12
Component:: 110000 electrical system
Summary:: Sb - 05 - 004 speedometer recalibration. this document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. tire size change, rear carrier ratio change).
Bulletin:: 167-B0503-12
Component:: 060000 engine (pws)
Summary:: Sb ? 05 - 010 correction to workshop manuals for the j08e engine. a) resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 ohms b) illustration of the air intake pre-heater terminal should be revised. c) r
Bulletin:: 167-B0504-12
Component:: 063000 engine and engine cooling:exhaust system
Summary:: Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
Bulletin:: 167-B0505-12
Component:: 356000 equipment adaptive
Summary:: Sb ? 05 - 007 design change of water pipe for j08e
Bulletin:: 167-B0506-12
Component:: 060000 engine (pws)
Summary:: Sb ? 05 - 008 this document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
Bulletin:: 167-B0508-12
Component:: 106000 power train:axle assembly
Summary:: Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
Bulletin:: 167-B0601-12
Component:: 060000 engine and engine cooling
Summary:: Sb ? 06 - 001 design change of engine oil cooler housing. the casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. these grooves aid in the retentio
Bulletin:: 167-B0602-12
Component:: 061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:: Sb ? 06 - 002 fuel filter usage. this bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
Bulletin:: 167-B0803-12
Component:: 203000 wheels:lugs/nuts/bolts
Summary:: Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
Bulletin:: 167-T1202-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: 12-001 recording the burner event log (bel) on 11-13my trucks
Bulletin:: 167-T1204-12
Component:: 062000 engine and engine cooling:cooling system
Summary:: 12 - 002 diagnosis procedure for p2457. some engines may erroneously record a p2457 dtc in the ecu. this fault condition is due to ecu software misdetection of egr cooler efficiency.
Bulletin:: 167-T1303-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: 13-003 injection quantity test 11 thru 14my
Bulletin:: 167-B1423-12
Component:: 118000 electrical system: software
Summary:: Sb-14-005 2011my-2015my conventional keyless entry programming
Bulletin:: 167-B1423-12
Component:: 353000 equipment:electrical
Summary:: Sb-14-005 2011my-2015my conventional keyless entry programming
Bulletin:: 167-B1426-12
Component:: 162810 structure:body:hood:hinge and attachments
Summary:: Sa-14-026 the broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. there is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. the revised p
Bulletin:: 167-B1415-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?s p0340 and p0341. you are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
Bulletin:: 167-B1503-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc p2123)
Bulletin:: 167-B1504-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc p0421)
Bulletin:: 167-B1510-12
Component:: 063130 engine and engine cooling:exhaust system:emission control:gas recirculation valve (egr valve)
Summary:: Sb-15-010 some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat p1604 dtc (diagnostic trouble code) stored in the engine ecu. a heated e
Bulletin:: 167-B1511-12
Component:: 011000 steering:wheel and handle bar
Summary:: Sb-15-011 the following tsb (technical service bulletin) outlines the inspection method for steering wheel free play and the adjustment procedure of the steering gear.
Bulletin:: 167-B1521-12
Component:: 020000 suspension
Summary:: Sb-15-022 in the rare event that a subject vehicle equipped with the 23k comfort ride air suspension experiences a premature main leaf failure, a 23k hd comfort ride air suspension may be installed with prior approval from hmm qa.
Bulletin:: 167-B1523-12
Component:: 060000 engine and engine cooling
Summary:: Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. an improved head gasket has been made available as a servic
Bulletin:: 167-B1528-12
Component:: 353000 equipment:electrical
Summary:: Sb-15-031 foreign debris in the def (diesel exhaust fluid) tank may cause the scr (selective catalyst reduction) system to malfunction. this can result in dtc?s (diagnostic trouble codes) p20e8 or p20e9 - def pressure abnormality. an inlet
Bulletin:: 167-B1529-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: Sb-15-032 troubleshooting information and inspection procedure of the dtc/p2030 were revised.
Bulletin:: 167-B1621-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: Sb-16-010 correction of the inspection of the dpr filter.
Bulletin:: 167-B1625-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: Sb-16-021 correction of workshop manual for hino600 series correction of electrical wiring diagram
Bulletin:: 167-B1101-12
Component:: 090000 fuel system, other
Summary:: Sb-11-002 requirements of biofuel usage for 2008my thru 2012my vehicles all applied models
Bulletin:: 167-B1301-12
Component:: 050000 parking brake
Summary:: Sb-13-003 in some cases the parking brake lamp indicator may remain illuminated with the parking brake lever in the ?off? position. this tsb (technical service bulletin) will provide instructions for installing an enhanced parking brake swi
Bulletin:: 167-B1307-12
Component:: 103300 power train:automatic transmission:gear position indication (prndl)
Summary:: 13-008 design change of the idler gear case and idler gear bolt. abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. therefore, an enhancement to the case and bolt were carried out. the idle
Bulletin:: 167-B1312-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. all models
Bulletin:: 167-T0706-12
Component:: 355200 equipment:other:owners/service/other manual
Summary:: 07 - 006 voltage drop test
Bulletin:: 167-T1513-12
Component:: 100000 power train
Summary:: Tt-15-014 the transmission dtc?s p0974 and p0986, may be found on 12my-15my coe models. there could also be a complaint of low power and erratic shifting. these diagnostic codes may be set due to low voltage between the transmission case an
Bulletin:: 167-T1514-12
Component:: 162000 structure:body
Summary:: Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. in some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t

Home | Privacy