2011 HINO NE8J Recalls (7)

Campaign:
11V011000 on 01/12/2011
Component:
Power train:automatic transmission
Manufactured:
05/31/2010 - 12/09/2010
Affected:
23
Defect:
Hino is recalling certain model year 2011 ne8j and nj8j trucks manufactured from june 1, 2010, through december 10, 2010, and equipped with certain eaton transmissions with park feature. the reverse idler shaft may contact the park feature and the two components may bind, preventing the park feature from engaging.
Consequence:
If a brake is not used or is defective and the park pawl does not engage, the vehicle may be able to move and potentially cause injury to the operator or persons in the vicinity of the moving vehicle or damage property.
Correction:
Hino will notify owners and repair all vehicles that contain this condition free of charge. the safety recall began on march1, 2011. owners may contact hino at 248-699-9330.
Notes:
Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .
Campaign:
11V320000 on 06/12/2011
Component:
Suspension:front:wheel bearing
Manufactured:
02/08/2011 - 03/30/2011
Affected:
237
Defect:
Hino is recalling certain model year 2011 ne8j vehicles. the front axle outer wheel bearing cone rollers may not have been properly heat treated. the suspect bearing cones have the date code "zj" on the major face of the inner bearing race just following the "canada" stamp.
Consequence:
Without heat treating, a bearing may suffer pre-mature failure which may result in a fire at the wheel or wheel separation that could lead to a crash.
Correction:
Hino will notify owners and repair the vehicles free of charge. the safety recall began on april 19, 2012. owners may contact hino motors at 1-248-699-9330.
Notes:
Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .
Campaign:
11V549000 on 11/16/2011
Component:
Steering
Manufactured:
02/15/2011 - 03/02/2011
Affected:
62
Defect:
Hino motors is recalling certain model year 2011-2012 ne8j trucks. during the assembly process, the steering attachment bolts may have been insufficiently torqued.
Consequence:
Insufficient torque of the steering arm bolts may result in bolt fatigue and fracture and/or arm separation, thereby potentially resulting in loss of steering control, increasing the risk of a crash.
Correction:
Hino will notify owners, and dealers will repair or replace the steering arm bolts free of charge. the safety recall began on april 19, 2012. owners may contact hino at 1-248-699-9390.
Notes:
Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .
Campaign:
12V555000 on 12/03/2012
Component:
Electrical system:battery:cables
Manufactured:
08/17/2003 - 11/15/2011
Affected:
35,142
Defect:
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:
If the b+ circuit shorts to ground, it may lead to a fire.
Correction:
Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:
Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:
12V555000 on 12/03/2012
Component:
Electrical system:wiring
Manufactured:
08/17/2003 - 11/15/2011
Affected:
35,142
Defect:
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:
If the b+ circuit shorts to ground, it may lead to a fire.
Correction:
Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:
Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:
14V791000 on 12/14/2014
Component:
Parking brake
Manufactured:
08/25/2003 - 05/13/2014
Affected:
8,140
Defect:
Hino motor sales u.s.a., inc. (hino) is recalling certain model year 2005-2015 hino nd8j, ne8j, and nf8j trucks manufactured august 26, 2003, to may 14, 2014. in the affected vehicles, components of the parking brake handle assembly may wear, resulting in either the parking brake unexpectedly releasing when engaged or preventing the parking brake from fully engaging.
Consequence:
Either parking brake condition may result in the vehicle rolling unexpectedly, increasing the risk of a crash.
Correction:
Hino will notify owners, and dealers will install a new parking brake lever that contains a two-way damper and a roller at the cable joining pin, free of charge. the recall began february 2, 2015. owners may contact hino customer service at 1-248-699-9330. hino's number for this recall is a9970. note: this recall supersedes 13v-614.
Notes:
Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:
17V607000 on 09/28/2017
Component:
Engine and engine cooling:engine:diesel
Manufactured:
02/03/2010 - 01/06/2011
Affected:
3,224
Defect:
Hino motor sales u.s.a., inc. (hino) is recalling certain 2011-2012 ne8j, nj8j, and nv8j trucks. the engines have a wrist pin bushings in the connecting rods that may shift and cause excessive cylinder wear.
Consequence:
Excessive wear of the cylinders can result in engine failure, increasing the risk of a crash.
Correction:
Hino will notify owners, and dealers will inspect and, as necessary, replace the connecting rods. interim notices informing owners of the safety risk were mailed november 27, 2017. the recall began on march 19, 2018. owners may contact hino customer service at 1-248-699-9300. hino's number for this recall is aa860.
Notes:
Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.

2011 HINO NE8J TSBs (83)

Bulletin:
RCB-002-13
Component:
118000 electrical system: software
Summary:
Hino trucks: malfunction indicator lamp (mil) may be illuminating. vehicle may also experience reduced power. performing a software enhancement should correct this problem. *kb
Bulletin:
RCB-007-11
Component:
063130 engine and engine cooling:exhaust system:emission control:gas recirculation valve (egr valve)
Summary:
Hino trucks: condensation that develops when the vehicle is running on the exhaust gas recirculation (egr) may freeze during below freezing temperatures causing the malfunction indicator lamp (mil) to illuminate. *kb
Bulletin:
RCB-008-12
Component:
118000 electrical system: software
Summary:
Hino trucks: malfunction indicator lamp (mil) possibly illuminating during cold temperatures. software update for the dosing control unit (dcu) could solve this problem. *kb
Bulletin:
RCB-009-12
Component:
118000 electrical system: software
Summary:
Hino: software update for burner control unit (bcu). ignition of the burner system may perform improperly and cause a mil light to illuminate in the instrument cluster. *kb
Bulletin:
RCB-006-11
Component:
063000 engine and engine cooling:exhaust system
Summary:
Hino: in below freezing ambient temperatures the diesel exhaust fluid (def) may freeze in the supply. installing the def line cover kit installation should correct the issue. *kb
Bulletin:
RCB-001-13
Component:
061200 engine and engine cooling:engine:diesel
Summary:
Hino: soot accumulates on the igniter. burner ignition could perform improperly. replacement of the diesel particulate regeneration (dpr) igniter plugs. *kb
Bulletin:
167-A1401-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
A-15-008 a subject vehicle may experience dpr (diesel particulate reduction) system related issues in extreme cold weather conditions. if a good fuel quality is being used and persistent fuel gelling has been confirmed to be the cause of t
Bulletin:
167-P1602-12
Component:
060000 engine (pws)
Summary:
13-008 injection pump drive case. please note the following part number changes to the injection pump bearing case. not replacing the correct replacement parts will result in major engine damage. the hino ordering system has been modified
Bulletin:
167-R1302-12
Component:
060000 engine (pws)
Summary:
Rcb-002-13 ecu enhancement. during vehicle operation, the malfunction indicator lamp (mil) may illuminate and/or the vehicle will experience reduced power.
Bulletin:
167-R1303-12
Component:
063000 engine and engine cooling:exhaust system
Summary:
Rcb-007-11 during below freezing ambient temperature operation, condensation may develop in the exhaust gas recirculation (egr) inlet pipe and egr valve. when the engine is shut off, this condensation may freeze. upon a cold engine restart,
Bulletin:
167-R1304-12
Component:
060000 engine (pws)
Summary:
Rcb-006-11 during extreme below freezing ambient temperatures, the diesel exhaust fluid (def) may begin to freeze in the supply or return line coming from the def tank. this situation may result in illumination of the malfunction indicator
Bulletin:
167-R1305-12
Component:
116000 electrical system:ignition
Summary:
Rcb-001-13 when soot accumulates on the igniter surface, the burner ignition may perform improperly, which may cause the mil (malfunction indicator lamp) in the instrument cluster of the vehicle to turn ?on?. to promote improved ignition du
Bulletin:
167-R1502-12
Component:
060000 engine (pws)
Summary:
Aa0f0 dpr clogging may occur due to an increase in the amount of soot in the exhaust gas as a result of engine component degradation. in order to reduce the soot in the exhaust gas during this situation, even when the engine components are
Bulletin:
167-R1504-12
Component:
110000 electrical system
Summary:
Scb-006-15 1) dpr system (diesel particulate regeneration) manual regeneration may not complete; this occurs when the bcu temporally detects sticking of the cav (combustion air valve). this mis-detection will cause regeneration to be suspen
Bulletin:
167-B0501-12
Component:
060000 engine (pws)
Summary:
05 - 011 corrections to workshop manuals for j08 engines. the standard gap between ends of the second piston ring and the oil ring.
Bulletin:
167-B0502-12
Component:
110000 electrical system
Summary:
Sb - 05 - 004 speedometer recalibration. this document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. tire size change, rear carrier ratio change).
Bulletin:
167-B0503-12
Component:
060000 engine (pws)
Summary:
Sb ? 05 - 010 correction to workshop manuals for the j08e engine. a) resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 ohms b) illustration of the air intake pre-heater terminal should be revised. c) r
Bulletin:
167-B0504-12
Component:
063000 engine and engine cooling:exhaust system
Summary:
Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
Bulletin:
167-B0505-12
Component:
356000 equipment adaptive
Summary:
Sb ? 05 - 007 design change of water pipe for j08e
Bulletin:
167-B0506-12
Component:
060000 engine (pws)
Summary:
Sb ? 05 - 008 this document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
Bulletin:
167-B0508-12
Component:
106000 power train:axle assembly
Summary:
Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
Bulletin:
167-B0601-12
Component:
060000 engine and engine cooling
Summary:
Sb ? 06 - 001 design change of engine oil cooler housing. the casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. these grooves aid in the retentio
Bulletin:
167-B0602-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Sb ? 06 - 002 fuel filter usage. this bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
Bulletin:
167-B0803-12
Component:
203000 wheels:lugs/nuts/bolts
Summary:
Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
Bulletin:
167-B1202-12
Component:
023100 suspension:multiple axle:torque arm
Summary:
Sb-12-001 correction of 2011my workshop manual (addition of tightening torque for def injector mounting bolt)
Bulletin:
167-B1203-12
Component:
110000 electrical system
Summary:
Sb-12-002 flame temperature sensor replacement guidelines. 2. condition: many flame temperature sensors are being replaced for burner failure (as shown below) but in many cases the sensor itself is not the issue. please follow the guidelin
Bulletin:
167-B1414-12
Component:
356000 equipment adaptive
Summary:
Sb-14-020 when replacing a broken hood grille, an enhanced replacement hood grille is available. this procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
Bulletin:
167-B1416-12
Component:
060000 engine (pws)
Summary:
Sb-14-013 "dpr damage", "burner misfire due to excessive soot on the burner igniter surface", and "dpr push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. in order to red
Bulletin:
167-B1419-12
Component:
203000 wheels:lugs/nuts/bolts
Summary:
Sb-14-009 during inspection of one of the subject vehicles, the technician may notice loose or missing retainer nuts or bolts on the no.1 cross member (directly behind the front bumper). in the event that loose nuts are found, it will be ne
Bulletin:
167-B1420-12
Component:
118000 electrical system: software
Summary:
Sb-14-014 subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. in these cases, there will be no indicators showing why manual regeneration will not
Bulletin:
167-T1201-12
Component:
063100 engine and engine cooling:exhaust system:emission control
Summary:
12-004 "exhaust gas temp" (dpr outlet) reading error
Bulletin:
167-T1202-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
12-001 recording the burner event log (bel) on 11-13my trucks
Bulletin:
167-T1301-12
Component:
060000 engine and engine cooling
Summary:
13-001 scr coolant hose clamp.
Bulletin:
167-T1303-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
13-003 injection quantity test 11 thru 14my
Bulletin:
167-R1401-12
Component:
080000 fuel system, diesel
Summary:
Rcb-004-13 when a subject vehicle is operated at low temperatures, the def (diesel exhaust fluid) in the def hose may freeze, which may cause the on-board diagnostic system to work improperly, and may cause the mil (malfunction indicator la
Bulletin:
167-R1404-12
Component:
080000 fuel system, diesel
Summary:
Rcb-005-14 when a subject vehicle is operated at low temperatures, the def (diesel exhaust fluid) in the def hose may freeze, which may cause the on-board diagnostic system to work improperly, and may cause the mil (malfunction indicator la
Bulletin:
167-B1407-12
Component:
110000 electrical system
Summary:
Sb-14-025 subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?s (diagnostic trouble codes)
Bulletin:
167-B1408-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-14-028 correction of workshop manual for 2011- 2015 my. troubleshooting information and inspection procedure of the dtc/p207f were revised.
Bulletin:
167-B1407-12
Component:
110000 electrical system
Summary:
Sb-14-025 subject vehicles may exhibit electrical symptoms which can include, but are not limited to erratic operation of the exterior lamps, warning lamps illuminated in the instrument cluster, or erroneous dtc?s (diagnostic trouble codes)
Bulletin:
167-B1408-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-14-028 correction of workshop manual for 2011- 2015 my. troubleshooting information and inspection procedure of the dtc/p207f were revised.
Bulletin:
167-B1401-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-14-029 correction of workshop manual for 2011 - 2015 my. troubleshooting information and inspection procedures for the dtc p2201 and p2214 were revised.
Bulletin:
167-B1402-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-14-007 procedure for auto regeneration is possible but not manual regeneration.
Bulletin:
167-B1403-12
Component:
110000 electrical system
Summary:
Sb-14-016 in the event that one of the subject vehicles is driven while the abs warning lamp is illuminated, operation of the torque converter clutch will be suspended. driving the vehicle with an abs warning lamp illuminated can lead to ov
Bulletin:
167-B1419-12
Component:
162200 structure:body:bumpers
Summary:
Sb-14-009 during inspection of one of the subject vehicles, the technician may notice loose or missing retainer nuts or bolts on the no.1 cross member (directly behind the front bumper). in the event that loose nuts are found, it will be ne
Bulletin:
167-B1420-12
Component:
118000 electrical system: software
Summary:
Sb-14-014 subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. in these cases, there will be no indicators showing why manual regeneration will not
Bulletin:
167-B1423-12
Component:
118000 electrical system: software
Summary:
Sb-14-005 2011my-2015my conventional keyless entry programming
Bulletin:
167-B1419-12
Component:
160000 structure
Summary:
Sb-14-009 during inspection of one of the subject vehicles, the technician may notice loose or missing retainer nuts or bolts on the no.1 cross member (directly behind the front bumper). in the event that loose nuts are found, it will be ne
Bulletin:
167-B1420-12
Component:
353000 equipment:electrical
Summary:
Sb-14-014 subject vehicles may exhibit a concern where manual regeneration does not complete within one hour of depressing the manual regeneration button. in these cases, there will be no indicators showing why manual regeneration will not
Bulletin:
167-B1423-12
Component:
353000 equipment:electrical
Summary:
Sb-14-005 2011my-2015my conventional keyless entry programming
Bulletin:
167-B1426-12
Component:
162810 structure:body:hood:hinge and attachments
Summary:
Sa-14-026 the broken hood grille procedure (sb-14-020) has been revised to reuse the grille nuts (sz17906009) if possible. there is a limited quantity of the nuts available and it has been confirmed that the nuts are reusable. the revised p
Bulletin:
167-B1414-12
Component:
162800 structure:body:hood
Summary:
Sb-14-020 when replacing a broken hood grille, an enhanced replacement hood grille is available. this procedure should be used when installing this enhanced grille to make certain that the hood grille is correctly installed.
Bulletin:
167-B1415-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?s p0340 and p0341. you are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
Bulletin:
167-B1416-12
Component:
070000 fuel system, gasoline
Summary:
Sb-14-013 "dpr damage", "burner misfire due to excessive soot on the burner igniter surface", and "dpr push out" may occur due to the increase in the amount of soot in exhaust gas as a result of engine component degradation. in order to red
Bulletin:
167-B1503-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc p2123)
Bulletin:
167-B1504-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc p0421)
Bulletin:
167-B1510-12
Component:
063130 engine and engine cooling:exhaust system:emission control:gas recirculation valve (egr valve)
Summary:
Sb-15-010 some vehicles that operate in extreme cold weather climates may exhibit ice accumulation on the egr (exhaust gas recirculation) butterfly plate with a repeat p1604 dtc (diagnostic trouble code) stored in the engine ecu. a heated e
Bulletin:
167-B1513-12
Component:
350000 equipment
Summary:
Sb-15-014 correction of workshop manual for 2011my-2014my (addition and correction of burner system)
Bulletin:
167-B1518-12
Component:
162000 structure:body
Summary:
Sb-15-019 reinforcement brackets and fiberglass repair methods have been made available to address hood crack concerns. in the event a subject vehicle experiences cracking of the hood near the hinges, this repair procedure should be used
Bulletin:
167-B1521-12
Component:
020000 suspension
Summary:
Sb-15-022 in the rare event that a subject vehicle equipped with the 23k comfort ride air suspension experiences a premature main leaf failure, a 23k hd comfort ride air suspension may be installed with prior approval from hmm qa.
Bulletin:
167-B1523-12
Component:
060000 engine and engine cooling
Summary:
Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. an improved head gasket has been made available as a servic
Bulletin:
167-B1528-12
Component:
353000 equipment:electrical
Summary:
Sb-15-031 foreign debris in the def (diesel exhaust fluid) tank may cause the scr (selective catalyst reduction) system to malfunction. this can result in dtc?s (diagnostic trouble codes) p20e8 or p20e9 - def pressure abnormality. an inlet
Bulletin:
167-B1529-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-15-032 troubleshooting information and inspection procedure of the dtc/p2030 were revised.
Bulletin:
167-B1601-12
Component:
070000 fuel system, gasoline
Summary:
Sb-16-007 if dtc(diagnostic trouble code) p0611:fuel injector driver charge circuit - circuit low has set in the engine ecu(electronic control unit) and the workshop manual diagnostic procedure has led to ecu replacement, an enhanced engine
Bulletin:
167-B1602-12
Component:
118000 electrical system: software
Summary:
Sb-16-015 enhanced dcu (dosing control unit) software has been released.illumination of the check engine light. the dcu may falsely detect an issue and record any of the 3 following dtc?s in the dcu. p142a(def pump temperature sensor - out
Bulletin:
167-B1618-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Addition of detailed explanation of the fuel pipe installation.
Bulletin:
167-B1619-12
Component:
020000 suspension
Summary:
Sb-16-006 some vehicles built before january 2016 and equipped with a leaf spring rear suspension may experience a dislodged or missing spring pad. as an enhancement, the rear axle leaf spring hanger design has been changed to eliminate the
Bulletin:
167-B1621-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-16-010 correction of the inspection of the dpr filter.
Bulletin:
167-B1625-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-16-021 correction of workshop manual for hino600 series correction of electrical wiring diagram
Bulletin:
167-B1626-12
Component:
110000 electrical system
Summary:
sb-16-022 a subject vehicle may experience an external fuel leak from the burner atomization module assembly, specifically the fuel pressure regulator. this repair procedure outlines replacement of the fuel pressure regulator seals while t
Bulletin:
167-B1101-12
Component:
090000 fuel system, other
Summary:
Sb-11-002 requirements of biofuel usage for 2008my thru 2012my vehicles all applied models
Bulletin:
167-B1103-12
Component:
060000 engine (pws)
Summary:
Sb-11-005 information and procedure for checking and cleaning of the breather hose on the def tank. the breather hose can clog up with crystallized def, which can cause the def to overflow from the tank when filling and not allow the tank t
Bulletin:
167-B1301-12
Component:
050000 parking brake
Summary:
Sb-13-003 in some cases the parking brake lamp indicator may remain illuminated with the parking brake lever in the ?off? position. this tsb (technical service bulletin) will provide instructions for installing an enhanced parking brake swi
Bulletin:
167-B1304-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
13-005 correction of workshop manual. correction of maintenance interval for dpr filter and def filter element in the workshop manual.
Bulletin:
167-B1305-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
13-006 correction of workshop manual. correction of the terminals to be inspected in the diagnosis procedure of can communication line. (for dtc u0101)
Bulletin:
167-B1306-12
Component:
070000 fuel system, gasoline
Summary:
13-007 correction of workshop manuals. addition of cautions for filling the def. (the actions to be taken if diesel fuel has been mistakenly added into the def tank.)
Bulletin:
167-B1307-12
Component:
103300 power train:automatic transmission:gear position indication (prndl)
Summary:
13-008 design change of the idler gear case and idler gear bolt. abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. therefore, an enhancement to the case and bolt were carried out. the idle
Bulletin:
167-B1308-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
13-010 correction of workshop manuals. hint: in case the dtc p204f has being recorded in the engine ecu, but no dtc has been detected in the dcu, it is safe to think that power supply to the dcu was interrupted before the dtc was recorde
Bulletin:
167-B1311-12
Component:
220000 seats
Summary:
13-014 an audible seat squeak may occur from the driver seat and/or single occupant passenger seat while driving over rough roads. this audible squeak may be occurring because of contact between the seat back frame and the seat base assembl
Bulletin:
167-B1312-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. all models
Bulletin:
167-T0706-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
07 - 006 voltage drop test
Bulletin:
167-T1514-12
Component:
162000 structure:body
Summary:
Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. in some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
Bulletin:
167-T1603-12
Component:
110000 electrical system
Summary:
Tt-16-001
Bulletin:
167-T1406-12
Component:
060000 engine and engine cooling
Summary:
14-002 electrical issues or false starter engagement due to coolant intrusion into junction box

Home | Privacy