2009 HINO NV8J Recalls (7)

Campaign:
08V471000 on 09/21/2008
Component:
Power train:driveline
Manufactured:
02/04/2007 - 02/28/2008
Affected:
1,195
Defect:
Hino is recalling 1,195 my 2007-2009 nv8j trucks. during the manufacturing process, the propeller shaft bolts may not have been properly tightened during the manufacturing process.
Consequence:
If the bolts were to loosen, it could cause a vibration in the driveline. if this vibration were ignored, the propeller shaft could separate from the mating flange. this could potentially result in damage to property and/or result in a crash.
Correction:
Dealers will replace the propeller shaft bolts. the recall began on october 14, 2008. owners may contact hino at 1-248-699-9300.
Notes:
Hino recall no. m0120.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.

Campaign:
08V667000 on 12/15/2008
Component:
Suspension:rear
Manufactured:
10/21/2007 - 09/03/2008
Affected:
130
Defect:
Hino is recalling 130 my 2008-2009 nd8j, ne8j, nj8j, and nv8j conventional trucks. the rear axle u-bolts were not properly tightened. the lower spring seat may not contact the axle housing properly, producing a gap on the front or rear side of the axle housing.
Consequence:
This gap could allow the u-bolts to loosen and/or cause the lower spring seat to crack. the axle could become misaligned and/or separated from the mountings increasing the risk of a crash.
Correction:
Dealers will inspect the rear air suspension lower spring seat for a gap between the rear axle and lower spring seat. the u-bolts will be tightened to the specified torque. the recall began on january 19, 2009. owners may contact hino at 1-248-699-9330.
Notes:
Hino recall no. m0140.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Campaign:
10V154000 on 04/14/2010
Component:
Engine and engine cooling
Manufactured:
10/26/2007 - 07/14/2009
Affected:
571
Defect:
Hino is recalling certain model year 2008-2010 nv8j trucks equipped with allison 3000 rds automatic transmission. the drive coupler bolts may not have been properly tightened at the factory due to the incorrect tool possibly being used during the manufacturing process.
Consequence:
If the drive coupler bolts were to loosen it could cause a vibration in the driveline. if this vibration were ignored, the drive coupler bolts could shear and the coupling between the engine and torque converter would not transmit power. this ultimately could result in a crash.
Correction:
Hino will notify owners and dealers will repair the vehicles free of charge. the safety recall began on november 9, 2010. owners may contact hino at 1-248-699-9330.
Notes:
Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Campaign:
10V156000 on 04/15/2010
Component:
Engine and engine cooling:exhaust system
Manufactured:
07/15/2008 - 06/10/2009
Affected:
89
Defect:
Hino is recalling certain trucks with vertical exhaust pipes. certain bolts attaching the exhaust system to the truck may not have been properly tightened during the manufacturing process. the bolts could fail allowing the exhaust system to separate from the truck.
Consequence:
The exhaust system could fall onto the roadway and be struck by a following vehicle resulting in a crash.
Correction:
Hino will notify owners and dealers will repair the vehicles free of charge. the safety recall began on november 9, 2010. owners may contact hino at 248-699-9330.
Notes:
Hino recall no. m0180.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Campaign:
10V157000 on 04/15/2010
Component:
Power train:axle assembly:axle shaft
Manufactured:
08/17/2008 - 07/26/2009
Affected:
726
Defect:
Hino is recalling certain model year 2009-2010 nv8j trucks. the u-joint attachment bolts may not have been properly tightened during the manufacturing process.
Consequence:
If the bolts were to loosen it could cause a vibration in the driveline. if this vibration were ignored, the u-joint attachment bolts could shear and a portion of the propeller shaft could separate from the vehicle, thus falling onto the surface of the roadway and be struck by a vehicle resulting in a crash.
Correction:
Hino will notify owners and dealers will repair the vehicles free of charge. the safety recall began on november 9, 2010. owners may contact hino at 248-699-9330.
Notes:
Hino recall no. m0150.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Campaign:
12V555000 on 12/03/2012
Component:
Electrical system:battery:cables
Manufactured:
08/17/2003 - 11/15/2011
Affected:
35,142
Defect:
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:
If the b+ circuit shorts to ground, it may lead to a fire.
Correction:
Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:
Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.

Campaign:
12V555000 on 12/03/2012
Component:
Electrical system:wiring
Manufactured:
08/17/2003 - 11/15/2011
Affected:
35,142
Defect:
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:
If the b+ circuit shorts to ground, it may lead to a fire.
Correction:
Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:
Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.

2009 HINO NV8J TSBs (55)

Bulletin:
C-0005
Component:
022400 suspension:rear:shock absorber
Summary:
Hino trucks: incorrect shock absorbers on rear air suspensions. incorrect length shock absorbers may have been installed on the rear, driver and or passenger sides of subject trucks. *pe
Bulletin:
SB-R-0029
Component:
092200 fuel system, other:delivery:hoses, lines/piping, and fittings
Summary:
Hino trucks: the fuel tank breather hose(s) has been modified to prevent water from entering into the fuel tank(s). *pe
Bulletin:
SB-R-0030
Component:
090000 fuel system, other
Summary:
Hino truck: abnormal noise and vibration within the engine occurs due to the impeded operation of the injector needle which is caused by the formation of deposits in the fuel. *pe
Bulletin:
SB-R-0033
Component:
090000 fuel system, other
Summary:
Hino truck: the davco fuel filter assembly has been improved to prevent the effusion of air into the fuel system. *pe
Bulletin:
SB-R-0034
Component:
061000 engine and engine cooling:engine
Summary:
Hino trucks: abnormal noise and vibration within the engine occurs due to the impeded operation of the injector needle which is caused by the formation of deposits in the fuel. *pe
Bulletin:
SL-R-0031
Component:
092200 fuel system, other:delivery:hoses, lines/piping, and fittings
Summary:
Hino trucks: abnormal noise and vibration within the engine occurs due to the impeded operation of the injector needle which is caused by the formation of deposits in the fuel. *pe
Bulletin:
RCB-010-12
Component:
061200 engine and engine cooling:engine:diesel
Summary:
Hino: the engine control program could work improperly, causing check engine light (cel) to turn on, due to aging degradation of fuel injector and soot accumulating in diesel particulate filter (dpf). model 2008-2010 na6j, nb6j, nc6j, nd8
Bulletin:
167-P0803-12
Component:
060000 engine (pws)
Summary:
Ptb 01-08 complete engine assembly part numbers
Bulletin:
167-P1602-12
Component:
060000 engine (pws)
Summary:
13-008 injection pump drive case. please note the following part number changes to the injection pump bearing case. not replacing the correct replacement parts will result in major engine damage. the hino ordering system has been modified
Bulletin:
167-R0901-12
Component:
081100 fuel system, diesel:storage:tank assembly
Summary:
R0029 this bulletin includes instructions for the replacement of the fuel tank breather hose. if the vehicle is equipped with dual fuel tanks the breather hose must be replaced on both fuel tanks.
Bulletin:
167-R0902-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
R0034 this bulletin includes the instructions to complete the following. 1. determine the condition of the fuel injectors by monitoring quantity value using hino diagnostic explorer. 2. if the fuel injector condition is determined to be ?
Bulletin:
167-R0904-12
Component:
070000 fuel system, gasoline
Summary:
R0031 this bulletin includes the instructions for the replacement of the fuel system hoses on mdt vehicles equipped with dual fuel tanks.
Bulletin:
167-R0905-12
Component:
070000 fuel system, gasoline
Summary:
R0030 this bulletin includes the instructions for the replacement of the fuel system hoses.
Bulletin:
167-R0906-12
Component:
080000 fuel system, diesel
Summary:
R0033 this bulletin includes the instructions for replacement of davco fuel filter assembly components
Bulletin:
167-R1301-12
Component:
060000 engine (pws)
Summary:
Rcb-010-12 when soot accumulates in the dpf (diesel particulate filter) due to aging degradation of the fuel injector, the engine control program could potentially work improperly, which may cause the cel (check engine light) in the instrum
Bulletin:
167-R0801-12
Component:
020000 suspension
Summary:
C0005 this service campaign includes instructions for the inspection and replacement of the shock absorbers used on the rear air suspension.
Bulletin:
167-B0501-12
Component:
060000 engine (pws)
Summary:
05 - 011 corrections to workshop manuals for j08 engines. the standard gap between ends of the second piston ring and the oil ring.
Bulletin:
167-B0502-12
Component:
110000 electrical system
Summary:
Sb - 05 - 004 speedometer recalibration. this document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. tire size change, rear carrier ratio change).
Bulletin:
167-B0503-12
Component:
060000 engine (pws)
Summary:
Sb ? 05 - 010 correction to workshop manuals for the j08e engine. a) resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 ohms b) illustration of the air intake pre-heater terminal should be revised. c) r
Bulletin:
167-B0504-12
Component:
063000 engine and engine cooling:exhaust system
Summary:
Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
Bulletin:
167-B0505-12
Component:
356000 equipment adaptive
Summary:
Sb ? 05 - 007 design change of water pipe for j08e
Bulletin:
167-B0506-12
Component:
060000 engine (pws)
Summary:
Sb ? 05 - 008 this document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
Bulletin:
167-B0508-12
Component:
106000 power train:axle assembly
Summary:
Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
Bulletin:
167-B0601-12
Component:
060000 engine and engine cooling
Summary:
Sb ? 06 - 001 design change of engine oil cooler housing. the casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. these grooves aid in the retentio
Bulletin:
167-B0602-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Sb ? 06 - 002 fuel filter usage. this bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
Bulletin:
167-B0801-12
Component:
351300 equipment:recreational vehicle:lpg tank valve/gauge
Summary:
Sb ? 07 - 006 this bulletin provides diagnostic information for monitoring the engine running data to determine if the suction control valve is defective, and a service procedure for replacing the suction control valve when necessary. the s
Bulletin:
167-B0803-12
Component:
203000 wheels:lugs/nuts/bolts
Summary:
Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
Bulletin:
167-B0805-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
08 - 003 this document is to inform dealers and work shops to the update of inlet and outlet fuel pipes on the davco fuel filter assembly.
Bulletin:
167-B0806-12
Component:
092100 fuel system, other:delivery:fuel pump
Summary:
08 - 003 this document is to inform dealers and workshops of the design change to the supply pump and scv for j08e-tv, tw engine series.
Bulletin:
167-R1405-12
Component:
080000 fuel system, diesel
Summary:
Rcb-010-12 when soot accumulates in the dpf (diesel particulate filter) due to aging degradation of the fuel injector, the engine control program could potentially work improperly, which may cause the cel (check engine light) in the instrum
Bulletin:
167-B1404-12
Component:
103700 power train:automatic transmission:torque converter
Summary:
Sb-14-017 in the event that one of the subject vehicles is driven while the abs warning lamp is illuminated, operation of the torque converter clutch will be suspended. driving the vehicle with an abs warning lamp illuminated can lead to ov
Bulletin:
167-B1415-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?s p0340 and p0341. you are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
Bulletin:
167-B1503-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc p2123)
Bulletin:
167-B1504-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc p0421)
Bulletin:
167-B1514-12
Component:
100000 power train
Summary:
Sb-15-015 information of troubleshooting procedure for engine lacked power during the dpr automatic regeneration
Bulletin:
167-B1516-12
Component:
063200 engine and engine cooling:exhaust system:manifold/header/muffler/tail pipe
Summary:
Sb-15-017 new parts are available to prevent repeat exhaust manifold stud failures on the j05 engine. this bulletin provides instructions for an exhaust manifold attachment modification at the #1 and #4 cylinder locations. modifications to
Bulletin:
167-B1521-12
Component:
020000 suspension
Summary:
Sb-15-022 in the rare event that a subject vehicle equipped with the 23k comfort ride air suspension experiences a premature main leaf failure, a 23k hd comfort ride air suspension may be installed with prior approval from hmm qa.
Bulletin:
167-B1523-12
Component:
060000 engine and engine cooling
Summary:
Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. an improved head gasket has been made available as a servic
Bulletin:
167-T1420-12
Component:
162800 structure:body:hood
Summary:
Tt-14-021 this procedure illustrates a worst case scenario repair procedure, the process and materials being used are the same for all repairs. depending on the location of the repair, access may be limited in some cases. ensure that the re
Bulletin:
167-T1425-12
Component:
117000 digital instrument panel
Summary:
Tt-14-029 a subject vehicle at 200,000 miles may exhibit a "dpr maintenance" message displayed on the instrument cluster message center. the following procedure will instruct how to check the dpf and reset the displayed message.
Bulletin:
167-T1429-12
Component:
060000 engine (pws)
Summary:
Tt-14-033 when replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. in the event your replacement engine block does not have
Bulletin:
167-B1621-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-16-010 correction of the inspection of the dpr filter.
Bulletin:
167-B1625-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-16-021 correction of workshop manual for hino600 series correction of electrical wiring diagram
Bulletin:
167-R0902-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Rcb-003-11 this bulletin involves the inspection of the variable nozzle turbine (vnt) turbocharger linkrod along with the potential replacement of the vnt turbocharger assembly.
Bulletin:
167-B0901-12
Component:
060000 engine (pws)
Summary:
Sb - 09 - 003 this bulletin provides a procedure to modify the intake throttle valve.
Bulletin:
167-B0903-12
Component:
060000 engine and engine cooling
Summary:
Sb ? 09 - 001 this bulletin provides diagnostic information for monitoring the engine running data to determine if the suction control valve is defective, and a service procedure for replacing the suction control valve when necessary. the s
Bulletin:
167-B1101-12
Component:
090000 fuel system, other
Summary:
Sb-11-002 requirements of biofuel usage for 2008my thru 2012my vehicles all applied models
Bulletin:
167-B1307-12
Component:
103300 power train:automatic transmission:gear position indication (prndl)
Summary:
13-008 design change of the idler gear case and idler gear bolt. abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. therefore, an enhancement to the case and bolt were carried out. the idle
Bulletin:
167-B1312-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. all models
Bulletin:
167-T0706-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
07 - 006 voltage drop test
Bulletin:
167-T1514-12
Component:
162000 structure:body
Summary:
Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. in some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
Bulletin:
167-B1001-12
Component:
070000 fuel system, gasoline
Summary:
Sb ? 10 - 003 this bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel filter.
Bulletin:
167-B1003-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Sb-10-004 this document is to inform dealers and workshops of the procedures on applying an anti-seize lubricant to the vnt turbocharger link rod for the j05d and j08e engines.
Bulletin:
167-B1004-12
Component:
110000 electrical system
Summary:
10 - 001 starter assembly mounting nuts torque correction. the following is to inform you of the correction made to the workshop manuals
Bulletin:
167-T1612-12
Component:
060000 engine (pws)
Summary:
Tt-16-013 the procedure for installing the rocker shaft bolts into the cam housing has been updated. it is recommended to lightly lubricate the threads and flange of the bolts with clean engine oil before installing them. the torque specifi

Home | Privacy