2008 HINO NB6J Recalls (5)

Campaign:
07V209000 on 05/14/2007
Component:
Fuel system, gasoline:delivery:hoses, lines/piping, and fittings
Manufactured:
12/31/2006 - 03/20/2007
Affected:
61
Defect:
On certain trucks, due to insufficient bracket stiffness and over-tightening of the clip, the fuel pipe between the supply pump and the common rail may crack.
Consequence:
The engine warning light will alert the driver of the problem. if the warning light is ignored by the driver, this could ultimately cause a fire and the engine to stall.
Correction:
Dealers will inspect the bracket and the clip and replace the necessary parts free of charge. the recall began on may 1, 2008. owners may contact hino at 248-648-6430.
Notes:
Hino recall no. a5371.customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov.
Campaign:
07V508000 on 10/31/2007
Component:
Visibility:rearview mirrors/devices:exterior
Affected:
100
Defect:
On certain trucks, the side view mirrors may have been installed incorrectly possibly leading to the mirror glass detaching from the mirror housing.
Consequence:
If the mirror glass is lost, the driver may not be able to see traffic approaching from the rear increasing the risk of a crash.
Correction:
Dealers will inspect the side view mirrors and, if necessary, replace the mirror materials. the recall began on june 12, 2007. owners may contact hino at 1-248-648-6490.
Notes:
Hino recall no. m0100.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
08V195000 on 04/29/2008
Component:
Suspension:front
Affected:
16,805
Defect:
Hino is recalling 16,805 my 2005-2008 na6j, nb6j, nc6j, nd8j, ne8j, nj8j, and nv8j trucks. the two vertical right/left side front spring bracket bolts were not tightened properly during the assembly process. this may cause increased stress on the spring bracket which can lead to cracking of the bracket.
Consequence:
This could reduce steering control increasing the risk of a crash.
Correction:
Dealers will replace the vertical front spring bracket attachment bolts on right/left hanger brackets and re-torque all associated bolts free of charge. the recall began on september 8, 2008. owners may contact hino at 248-699-9300.
Notes:
Hino recall no. a5850.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
12V555000 on 12/03/2012
Component:
Electrical system:battery:cables
Manufactured:
08/17/2003 - 11/15/2011
Affected:
35,142
Defect:
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:
If the b+ circuit shorts to ground, it may lead to a fire.
Correction:
Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:
Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:
12V555000 on 12/03/2012
Component:
Electrical system:wiring
Manufactured:
08/17/2003 - 11/15/2011
Affected:
35,142
Defect:
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:
If the b+ circuit shorts to ground, it may lead to a fire.
Correction:
Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:
Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.

2008 HINO NB6J TSBs (47)

Bulletin:
R-0024
Component:
061200 engine and engine cooling:engine:diesel
Summary:
Hino trucks: under certain driving conditions, the engine control program does not provide satisfactory drivability characteristics. *pe
Bulletin:
SB-R-0029
Component:
092200 fuel system, other:delivery:hoses, lines/piping, and fittings
Summary:
Hino trucks: the fuel tank breather hose(s) has been modified to prevent water from entering into the fuel tank(s). *pe
Bulletin:
SB-R-0034
Component:
061000 engine and engine cooling:engine
Summary:
Hino trucks: abnormal noise and vibration within the engine occurs due to the impeded operation of the injector needle which is caused by the formation of deposits in the fuel. *pe
Bulletin:
SL-R-0032
Component:
072200 fuel system, gasoline:delivery:hoses, lines/piping, and fittings
Summary:
Hino trucks: abnormal noise and vibration within the engine occurs due to the impeded operation of the injector needle which is caused by the formation of deposits in the fuel. *pe
Bulletin:
RCB-010-12
Component:
061200 engine and engine cooling:engine:diesel
Summary:
Hino: the engine control program could work improperly, causing check engine light (cel) to turn on, due to aging degradation of fuel injector and soot accumulating in diesel particulate filter (dpf). model 2008-2010 na6j, nb6j, nc6j, nd8
Bulletin:
167-P0701-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Introduction of exchange turbocharger program. hino trucks is pleased to announce the introduction of the turbocharger exchange program for its 2005 ? 2008 model year trucks. effective june 21, 2007, the following turbocharger part numbers
Bulletin:
167-P0702-12
Component:
072100 fuel system, gasoline:delivery:fuel pump
Summary:
Revised warranty process ? denso fuel pumps & injector nozzles exchange denso fuel pumps & injector nozzles. effective immediately, fuel pumps and injector nozzles replaced under warranty are to be purchased from the memphis pdc. it is no
Bulletin:
167-P0703-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Tb-001-07 hino uses both davco and racor fuel/water separators on its vehicles. to determine the correct filter you must know which one is on the vehicle. the davco is shown on the left. the racor is shown on the right and has a primer butt
Bulletin:
167-P0802-12
Component:
021240 suspension:front:springs:leaf spring assembly
Summary:
Ptb 03-08 spring assemblies.
Bulletin:
167-P0803-12
Component:
060000 engine (pws)
Summary:
Ptb 01-08 complete engine assembly part numbers
Bulletin:
167-P0805-12
Component:
200000 wheels
Summary:
Ptb 08-08 2005-2008 quick reference guide correction to page 60
Bulletin:
167-P1602-12
Component:
060000 engine (pws)
Summary:
13-008 injection pump drive case. please note the following part number changes to the injection pump bearing case. not replacing the correct replacement parts will result in major engine damage. the hino ordering system has been modified
Bulletin:
167-R0901-12
Component:
081100 fuel system, diesel:storage:tank assembly
Summary:
R0029 this bulletin includes instructions for the replacement of the fuel tank breather hose. if the vehicle is equipped with dual fuel tanks the breather hose must be replaced on both fuel tanks.
Bulletin:
167-R0902-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
R0034 this bulletin includes the instructions to complete the following. 1. determine the condition of the fuel injectors by monitoring quantity value using hino diagnostic explorer. 2. if the fuel injector condition is determined to be ?
Bulletin:
167-R0903-12
Component:
070000 fuel system, gasoline
Summary:
R0032 this bulletin includes the instructions for the replacement of the fuel system hoses.
Bulletin:
167-R1301-12
Component:
060000 engine (pws)
Summary:
Rcb-010-12 when soot accumulates in the dpf (diesel particulate filter) due to aging degradation of the fuel injector, the engine control program could potentially work improperly, which may cause the cel (check engine light) in the instrum
Bulletin:
167-B0502-12
Component:
110000 electrical system
Summary:
Sb - 05 - 004 speedometer recalibration. this document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. tire size change, rear carrier ratio change).
Bulletin:
167-B0504-12
Component:
063000 engine and engine cooling:exhaust system
Summary:
Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
Bulletin:
167-B0508-12
Component:
106000 power train:axle assembly
Summary:
Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
Bulletin:
167-B0509-12
Component:
103000 power train:automatic transmission
Summary:
Sb ? 05 - 006 upon removal of a transmission assembly from the vehicle, inspection is required to confirm the presence and correct installation of the two dowel pins in the rear engine housing. in some rare cases one or both dowel pins may
Bulletin:
167-B0601-12
Component:
060000 engine and engine cooling
Summary:
Sb ? 06 - 001 design change of engine oil cooler housing. the casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. these grooves aid in the retentio
Bulletin:
167-B0602-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Sb ? 06 - 002 fuel filter usage. this bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
Bulletin:
167-B0702-12
Component:
021600 suspension:front:wheel bearing
Summary:
Sb - 07 - 005 the document is to inform the dealers about the change in material and tightening torque of the rocker arm support bolts and camshaft bearing cap bolts.
Bulletin:
167-B0704-12
Component:
103700 power train:automatic transmission:torque converter
Summary:
Sb - 07 - 008 correction in workshop manual for tightening torque of the injector clamp bolt
Bulletin:
167-B0802-12
Component:
063110 engine and engine cooling:exhaust system:emission control:crankcase (pcv)
Summary:
Sb - 08 - 001 this document is to inform dealers and workshops on the installation procedures for a crankcase breather (ventilator) anti freezing kit.
Bulletin:
167-B0803-12
Component:
203000 wheels:lugs/nuts/bolts
Summary:
Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
Bulletin:
167-B0804-12
Component:
060000 engine (pws)
Summary:
08 - 002 this document is to inform dealers and workshops of the design change to the exhaust gas recirculation (egr) valve and gasket for the j05d-tf engine series.
Bulletin:
167-R1405-12
Component:
080000 fuel system, diesel
Summary:
Rcb-010-12 when soot accumulates in the dpf (diesel particulate filter) due to aging degradation of the fuel injector, the engine control program could potentially work improperly, which may cause the cel (check engine light) in the instrum
Bulletin:
167-B1415-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?s p0340 and p0341. you are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
Bulletin:
167-B1509-12
Component:
113000 electrical system:starter assembly
Summary:
Sb-15-009 this bulletin provides the corrective action for a fluid overflow condition from the main housing breather at startup in cold ambient temperatures at or below +5f (-15c).
Bulletin:
167-B1514-12
Component:
100000 power train
Summary:
Sb-15-015 information of troubleshooting procedure for engine lacked power during the dpr automatic regeneration
Bulletin:
167-B1516-12
Component:
063200 engine and engine cooling:exhaust system:manifold/header/muffler/tail pipe
Summary:
Sb-15-017 new parts are available to prevent repeat exhaust manifold stud failures on the j05 engine. this bulletin provides instructions for an exhaust manifold attachment modification at the #1 and #4 cylinder locations. modifications to
Bulletin:
167-B1521-12
Component:
020000 suspension
Summary:
Sb-15-022 in the rare event that a subject vehicle equipped with the 23k comfort ride air suspension experiences a premature main leaf failure, a 23k hd comfort ride air suspension may be installed with prior approval from hmm qa.
Bulletin:
167-B1523-12
Component:
060000 engine and engine cooling
Summary:
Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. an improved head gasket has been made available as a servic
Bulletin:
167-T1420-12
Component:
162800 structure:body:hood
Summary:
Tt-14-021 this procedure illustrates a worst case scenario repair procedure, the process and materials being used are the same for all repairs. depending on the location of the repair, access may be limited in some cases. ensure that the re
Bulletin:
167-T1425-12
Component:
117000 digital instrument panel
Summary:
Tt-14-029 a subject vehicle at 200,000 miles may exhibit a "dpr maintenance" message displayed on the instrument cluster message center. the following procedure will instruct how to check the dpf and reset the displayed message.
Bulletin:
167-B1621-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-16-010 correction of the inspection of the dpr filter.
Bulletin:
167-R0901-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Rcb-003-11 this bulletin involves the inspection of the variable nozzle turbine (vnt) turbocharger linkrod along with the potential replacement of the vnt turbocharger assembly.
Bulletin:
167-B1101-12
Component:
090000 fuel system, other
Summary:
Sb-11-002 requirements of biofuel usage for 2008my thru 2012my vehicles all applied models
Bulletin:
167-B1307-12
Component:
103300 power train:automatic transmission:gear position indication (prndl)
Summary:
13-008 design change of the idler gear case and idler gear bolt. abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. therefore, an enhancement to the case and bolt were carried out. the idle
Bulletin:
167-B1312-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. all models
Bulletin:
167-T0704-12
Component:
200000 wheels
Summary:
07 - 004 abs wheel sensor (active fault 3-1 thru 3-4)
Bulletin:
167-T0705-12
Component:
125100 exterior lighting:brake lights:switch
Summary:
07 - 005 no throttle response (brake light switch)
Bulletin:
167-T0706-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
07 - 006 voltage drop test
Bulletin:
167-T0707-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
07 - 008 dx report ? exporting, saving and printing from past work information
Bulletin:
167-T1514-12
Component:
162000 structure:body
Summary:
Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. in some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
Bulletin:
167-T1612-12
Component:
060000 engine (pws)
Summary:
Tt-16-013 the procedure for installing the rocker shaft bolts into the cam housing has been updated. it is recommended to lightly lubricate the threads and flange of the bolts with clean engine oil before installing them. the torque specifi

Home | Privacy