2006 HINO NE8J Recalls (11)

Campaign:
05V356000 on 08/09/2005
Component:
Suspension:front:wheel bearing
Manufactured:
02/28/2005 - 07/30/2005
Affected:
46
Defect:
On certain chassis and cabs, the wheel bearings were oil-packed onto the front axle rather than grease lubricated as specified. it was later determined that the caliper mounting bolts were not properly torqued and the proper end play adjustment was not made.
Consequence:
This can cause the caliper mounting bolts to become loose and back out. the caliper could become disconnected from the rotor assembly which would cause a decrease in braking ability, increasing the risk of a crash.
Correction:
Dealers will torque all affected caliper mounting bolts and readjust each wheel for the proper end play adjustment. the recall began on september 6, 2005. owners should contact hino at 248-648-6400.
Notes:
Hino recall no. m0020.customers can also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236; (tty: 1-800-424-9153); or go to http://www.safercar.gov.
Campaign:
05V492000 on 10/23/2005
Component:
Electrical system:battery
Manufactured:
03/31/2005 - 07/31/2005
Affected:
577
Defect:
On certain trucks, the bolts that hold the battery box and bracket in place may not have been properly torqued at the time of assembly.
Consequence:
The battery box could become loose and possibly fall resulting in a crash without warning.
Correction:
Dealers will inspect and retorqued all bolts. the recall began on october 27, 2005. owners may contact hino at 248-648-6430.
Notes:
Hino recall no. m0040.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
06V157000 on 05/09/2006
Component:
Engine and engine cooling
Manufactured:
10/21/2003 - 06/09/2005
Affected:
3,930
Defect:
On certain trucks equipped with bando belt tensioner, corrosion or rust may develop on the tensioner spindle or bushing causing the auto tensioner to become stiff or bind. this can cause the drive belt to suddenly come off or the auto tensioner mounting bolts could suddenly break.
Consequence:
If the drive belt comes off, the alternator warning lamp will illuminate. if the warning is ignored, this condition could ultimately result in a loss of vehicle power (engine stall) increasing the risk of a crash.
Correction:
Dealers will replace the auto tensioner, install upgraded mounting bolts, and replace the accessory drive belt free of charge. the recall began on may 2, 2006. owners may contact hino motors at 248-648-6430. this campaign has been superseded - please see 07v208.
Notes:
Hino motors recall no. a4790.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
06V169000 on 05/17/2006
Component:
Steering:linkages
Manufactured:
09/30/2004 - 03/24/2006
Affected:
5,072
Defect:
On certain trucks, during assembly, the drag link attachment nuts at the pitman arm and steering arm may have been incorrectly torqued. residual grease and paint which was applied as a rust inhibitor on the steering arm may have contributed to a loss of torque after assembly.
Consequence:
Increased wear for the draglink connections can occur creating a noticeable increase in the amount of steering wheel free play. if this condition was ignored, a loss of steering control of the vehicle could occur which could result in a crash.
Correction:
Dealers will inspect the steering arm tightness and remove all grease and paint from the steering arms and retorque the draglink attachment nuts at the steering arm and pitman arm. the recall began on may 12, 2006. owners may contact hino at 1-248-648-6430.
Notes:
Hino recall no. m0050.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
06V360000 on 09/19/2006
Component:
Service brakes, air:supply:hoses, lines/piping, and fittings
Manufactured:
06/02/2005 - 08/29/2006
Affected:
746
Defect:
On certain cab and chassis trucks that were transported to the selling location or body company using a decking system (vehicles stacked on the rear of the lead truck for transport), the air brake lines may be disconnected so that the braking systems can be tied together with the other vehicles. when these vehicles arrive at their destination, the air brake lines are reconnected. these reconnections were not always being tightened to the proper torque. also, during this reconnection process, some of the abs wiring clips had been removed and not reinstalled.
Consequence:
Loose air brake lines can become disconnected or leak which could cause a decrease in braking ability or resulting in application of the parking brake without it being activated. this could result in a crash. also if the drive shaft bolts are left loose, the drive shaft could become disengaged making the vehicle immovable. if the abs sensors are not secured properly using the correct clips, the abs sensors could go out of alignment.
Correction:
Dealers will inspect the air brake lines, drive shaft bolts and abs sensor clips and tighten and repair if necessary. the recall began on september 15, 2006. owners may contact hino at 1-248-648-6430.
Notes:
Hino recall no. hs001.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
06V483000 on 12/26/2006
Component:
Structure
Manufactured:
02/28/2006 - 06/13/2006
Affected:
1,599
Defect:
On certain vehicles, during the stamping process, some crossmembers were manufactured with a deformation to the lower corners due to excessive wear of the stamping die. over time, if this condition were ignored, the structural integrity of the crossmembers could be compromised which could result in a loss of braking ability, separation of the propeller shaft and/or a loss of rear warning lamps.
Consequence:
Any of these occurrences could result in a crash.
Correction:
Dealers will inspect, correct, and replace the crossmembers. the recall began on december 4, 2006. owners may contact hino at 1-248-648-6400.
Notes:
Hino recall no. m0070.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
07V208000 on 05/14/2007
Component:
Engine and engine cooling
Manufactured:
10/21/2003 - 04/01/2007
Affected:
14,588
Defect:
On certain trucks equipped with bando belt tensioner, corrosion or rust may develop on the tensioner spindle or bushing causing the auto tensioner to become stiff or bind. this can cause the drive belt to suddenly come off or the auto tensioner mounting bolts could suddenly break.
Consequence:
If the drive belt comes off, the alternator warning lamp will illuminate. if the warning is ignored, this condition could ultimately result in a loss of vehicle power (engine stall) increasing the risk of a crash.
Correction:
Dealers will replace the auto tensioner, install upgraded mounting bolts, and replace the accessory drive belt free of charge. the recall began on april 25, 2007. owners may contact hino motors at 248-648-6430. note: this recall supersedes a previous campaign (please see 06v157).
Notes:
Hino recall no. a5340.customers mayalso contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
08V195000 on 04/29/2008
Component:
Suspension:front
Affected:
16,805
Defect:
Hino is recalling 16,805 my 2005-2008 na6j, nb6j, nc6j, nd8j, ne8j, nj8j, and nv8j trucks. the two vertical right/left side front spring bracket bolts were not tightened properly during the assembly process. this may cause increased stress on the spring bracket which can lead to cracking of the bracket.
Consequence:
This could reduce steering control increasing the risk of a crash.
Correction:
Dealers will replace the vertical front spring bracket attachment bolts on right/left hanger brackets and re-torque all associated bolts free of charge. the recall began on september 8, 2008. owners may contact hino at 248-699-9300.
Notes:
Hino recall no. a5850.customers may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov.
Campaign:
12V555000 on 12/03/2012
Component:
Electrical system:battery:cables
Manufactured:
08/17/2003 - 11/15/2011
Affected:
35,142
Defect:
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:
If the b+ circuit shorts to ground, it may lead to a fire.
Correction:
Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:
Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:
12V555000 on 12/03/2012
Component:
Electrical system:wiring
Manufactured:
08/17/2003 - 11/15/2011
Affected:
35,142
Defect:
Hino is recalling certain model year 2005 through 2013 medium duty trucks, models na6j, nb6j, nc6j, nd8j, ne8j, nj8j, nf8j, and nv8j, manufactured from august 18, 2003, through november 16, 2011. over time, the main b+ circuit from the battery to the starter could potentially short to ground due to wear that accumulates as a result of interference between the b+ circuit and its convoluted tubing sheath.
Consequence:
If the b+ circuit shorts to ground, it may lead to a fire.
Correction:
Hino will notify owners, and dealers will repair the vehicles free of charge. the recall began on january 17, 2013. owners may contact hino at 1-248-699-9390.
Notes:
Hino's recall campaign number is a8310.owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.
Campaign:
14V791000 on 12/14/2014
Component:
Parking brake
Manufactured:
08/25/2003 - 05/13/2014
Affected:
8,140
Defect:
Hino motor sales u.s.a., inc. (hino) is recalling certain model year 2005-2015 hino nd8j, ne8j, and nf8j trucks manufactured august 26, 2003, to may 14, 2014. in the affected vehicles, components of the parking brake handle assembly may wear, resulting in either the parking brake unexpectedly releasing when engaged or preventing the parking brake from fully engaging.
Consequence:
Either parking brake condition may result in the vehicle rolling unexpectedly, increasing the risk of a crash.
Correction:
Hino will notify owners, and dealers will install a new parking brake lever that contains a two-way damper and a roller at the cable joining pin, free of charge. the recall began february 2, 2015. owners may contact hino customer service at 1-248-699-9330. hino's number for this recall is a9970. note: this recall supersedes 13v-614.
Notes:
Owners may also contact the national highway traffic safety administration vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to www.safercar.gov.

2006 HINO NE8J TSBs (42)

Bulletin:
167-P0701-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Introduction of exchange turbocharger program. hino trucks is pleased to announce the introduction of the turbocharger exchange program for its 2005 ? 2008 model year trucks. effective june 21, 2007, the following turbocharger part numbers
Bulletin:
167-P0702-12
Component:
072100 fuel system, gasoline:delivery:fuel pump
Summary:
Revised warranty process ? denso fuel pumps & injector nozzles exchange denso fuel pumps & injector nozzles. effective immediately, fuel pumps and injector nozzles replaced under warranty are to be purchased from the memphis pdc. it is no
Bulletin:
167-P0703-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Tb-001-07 hino uses both davco and racor fuel/water separators on its vehicles. to determine the correct filter you must know which one is on the vehicle. the davco is shown on the left. the racor is shown on the right and has a primer butt
Bulletin:
167-P0704-12
Component:
356000 equipment adaptive
Summary:
Tb-04-07 an engineering change in connecting rods was made from a stud with nuts to fasten the cap, to a bolt only to fasten the cap. the connecting rods with the stud and nuts are no longer available. the two different styles are intercha
Bulletin:
167-P0802-12
Component:
021240 suspension:front:springs:leaf spring assembly
Summary:
Ptb 03-08 spring assemblies.
Bulletin:
167-P0803-12
Component:
060000 engine (pws)
Summary:
Ptb 01-08 complete engine assembly part numbers
Bulletin:
167-P0805-12
Component:
200000 wheels
Summary:
Ptb 08-08 2005-2008 quick reference guide correction to page 60
Bulletin:
167-P1602-12
Component:
060000 engine (pws)
Summary:
13-008 injection pump drive case. please note the following part number changes to the injection pump bearing case. not replacing the correct replacement parts will result in major engine damage. the hino ordering system has been modified
Bulletin:
167-B0501-12
Component:
060000 engine (pws)
Summary:
05 - 011 corrections to workshop manuals for j08 engines. the standard gap between ends of the second piston ring and the oil ring.
Bulletin:
167-B0502-12
Component:
110000 electrical system
Summary:
Sb - 05 - 004 speedometer recalibration. this document is to inform of the procedure to calibrate the pulse adjust module whenneeded (ex. tire size change, rear carrier ratio change).
Bulletin:
167-B0503-12
Component:
060000 engine (pws)
Summary:
Sb ? 05 - 010 correction to workshop manuals for the j08e engine. a) resistance between terminals of the air intake pre-heater relay should be 64.0 ? 96.0 ohms b) illustration of the air intake pre-heater terminal should be revised. c) r
Bulletin:
167-B0504-12
Component:
063000 engine and engine cooling:exhaust system
Summary:
Sb - 05 - 003 this document is to inform dealers and workshops on procedures to activate exhaust brake operation.
Bulletin:
167-B0505-12
Component:
356000 equipment adaptive
Summary:
Sb ? 05 - 007 design change of water pipe for j08e
Bulletin:
167-B0506-12
Component:
060000 engine (pws)
Summary:
Sb ? 05 - 008 this document is to inform the dealers about the addition of the pressure sensor cover and related part for the j08e engine.
Bulletin:
167-B0507-12
Component:
062100 engine and engine cooling:cooling system:radiator assembly
Summary:
Sb ? 05 - 009 this document is to inform dealers of the design change to the upper radiator tank and related parts.
Bulletin:
167-B0508-12
Component:
106000 power train:axle assembly
Summary:
Sb - 05 - 005 proper maintenance procedures for grease lubricated front axles
Bulletin:
167-B0601-12
Component:
060000 engine and engine cooling
Summary:
Sb ? 06 - 001 design change of engine oil cooler housing. the casting for the engine oil cooler housing has been revised to include 2 shallow machined grooves on both sides of the engine oil cooler housing. these grooves aid in the retentio
Bulletin:
167-B0602-12
Component:
061320 engine and engine cooling:engine:other fuel types:turbo-charger
Summary:
Sb ? 06 - 002 fuel filter usage. this bulletin provides technical information for proper fuel filter usage as well as an example of damage caused by foreign material allowed to enter the fuel system as a result of using an improper fuel fil
Bulletin:
167-B0705-12
Component:
103700 power train:automatic transmission:torque converter
Summary:
Sb - 07 - 002 service manual revision. outer wheel bearing nut torque reduction
Bulletin:
167-B0803-12
Component:
203000 wheels:lugs/nuts/bolts
Summary:
Sb - 08 - 005 this document is to inform dealers and workshops of the design change to the hood damper, support bolt and the addition of a support collar.
Bulletin:
167-T0601-12
Component:
090000 fuel system, other
Summary:
06-001 running out of fuel, dual tanks not equalizing
Bulletin:
167-T0603-12
Component:
350000 equipment
Summary:
06 - 008 abs extension harness no throttle response on 2007 air brake chassis with automatic transmissions when selector placed in drive. no cruise control on 2007 air brake chassis with manual transmissions.
Bulletin:
167-T0604-12
Component:
034510 service brakes, hydraulic:foundation components:disc:caliper
Summary:
06 - 009 correct brake calipers chassis experienced premature brake failure after a brake job was performed which included brake caliper replacement.
Bulletin:
167-T0605-12
Component:
090000 fuel system, other
Summary:
06 - 010 low power (fuel restriction)
Bulletin:
167-T0606-12
Component:
092100 fuel system, other:delivery:fuel pump
Summary:
06-011 high pressure fuel pump front seal failure
Bulletin:
167-B1415-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-14-003 the following is to inform you of the revision of the inspection procedure for the dtc?s p0340 and p0341. you are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to us
Bulletin:
167-B1503-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-15-002 correction of workshop manual for 2013 - 2015my (revision of troubleshooting procedure for the dtc p2123)
Bulletin:
167-B1504-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-15-003 correction of workshop manual for hino 2015my (revision of troubleshooting procedure for the dtc p0421)
Bulletin:
167-B1509-12
Component:
113000 electrical system:starter assembly
Summary:
Sb-15-009 this bulletin provides the corrective action for a fluid overflow condition from the main housing breather at startup in cold ambient temperatures at or below +5f (-15c).
Bulletin:
167-B1523-12
Component:
060000 engine and engine cooling
Summary:
Sb-15-026 a subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. an improved head gasket has been made available as a servic
Bulletin:
167-T1429-12
Component:
060000 engine (pws)
Summary:
Tt-14-033 when replacing an engine block with service part no., 11401e0380 there is potential that 2 rear oil passage plugs may be missing in the rear of the replacement engine block. in the event your replacement engine block does not have
Bulletin:
167-B1625-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-16-021 correction of workshop manual for hino600 series correction of electrical wiring diagram
Bulletin:
167-B1307-12
Component:
103300 power train:automatic transmission:gear position indication (prndl)
Summary:
13-008 design change of the idler gear case and idler gear bolt. abnormal load such as a stuck supply pump was applied to gear train then causing the bolt to loosen. therefore, an enhancement to the case and bolt were carried out. the idle
Bulletin:
167-B1312-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
Sb-13-009 this bulletin is to inform dealers and workshops of proper paint codes for all hino models. all models
Bulletin:
167-T0701-12
Component:
103700 power train:automatic transmission:torque converter
Summary:
07 ? 001 outer wheel bearing nut torque reduction. this tech tip provides information concerning the updated torque specification found in the hino workshop manual regarding the arvin meritor front non-drive steer axles mfs-06 and mfs-08
Bulletin:
167-T0704-12
Component:
200000 wheels
Summary:
07 - 004 abs wheel sensor (active fault 3-1 thru 3-4)
Bulletin:
167-T0705-12
Component:
125100 exterior lighting:brake lights:switch
Summary:
07 - 005 no throttle response (brake light switch)
Bulletin:
167-T0706-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
07 - 006 voltage drop test
Bulletin:
167-T0707-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
07 - 008 dx report ? exporting, saving and printing from past work information
Bulletin:
167-T0708-12
Component:
355200 equipment:other:owners/service/other manual
Summary:
06 - 012 speedometer pulse adapter conversion form
Bulletin:
167-T1514-12
Component:
162000 structure:body
Summary:
Tt-15-016 the purpose of this publication is to communicate the standard measuring positions on the hino chassis. in some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards t
Bulletin:
167-B1005-12
Component:
110000 electrical system
Summary:
10 - 002 starter assembly mounting nuts torque correction. the following is to inform you of the correction made to the workshop manuals

Home | Privacy