1980 MACK R SERIES Recalls (6)
- Campaign:
- 80V054000 on 05/15/1980
- Component:
- Steering:gear box (other than rack and pinion)
- Manufactured:
- 06/30/1976 - 12/31/1979
- Affected:
- 109
- Defect:
- The prefabricated pinch bolt clamp at the lower steering shaft lower yoke may not perform adequately when tightened to specifications. the clamp may then deform and loss of clamping force and steering shaft disengagement may result.
- Correction:
- Dealer will retrofit with lower steering shaft lower yokes that provide for integral pinch bolt installation in place of previous separately fabricated clamp for the pinch bolt.
- Notes:
- Vehicle description: trucks.system: steering; power steering shaft; fabricated pinch bolt clamp.consequences of defect: disengagement of the steering shaft may cause loss ofvehicle control without prior warning and, possibly, an accident.
- Campaign:
- 80V052000 on 07/17/1980
- Component:
- Parking brake:driveline:air
- Manufactured:
- 06/30/1979 - 12/31/1979
- Affected:
- 9,666
- Defect:
- On certain vehicles, the knob that operates the tractor park valve may break off, rendering the valve inoperable.
- Correction:
- Defective knobs will be replaced with an improved type, without charge to owner.
- Notes:
- Vehicle description: trucks.system: service brakes; tractor park valve control knob.consequences of defect: the purpose of the tractor park valve is to allow thedriver to apply the tractor spring emergency/parking brake independently of thetrailer emergency parking brakes. if the knob is broken, the tractor parkingbrakes cannot be applied. if parked on an incline and left unattended, vehiclecould roll free and cause accident and injury.
- Campaign:
- 80V162000 on 01/12/1981
- Component:
- Steering:wheel and handle bar
- Manufactured:
- 12/31/1979 - 10/31/1980
- Affected:
- 1,524
- Defect:
- The weld on the upper steering shaft where the female spline connects to the tube assembly may have been incorrectly positioned and actually missed the seam.
- Correction:
- The dealer will inspect and, if necessary, replace the affected shaft with one that has been properly welded, at no charge.
- Notes:
- Vehicle description: trucks.system: steering; upper steering shaft.consequences of defect: this condition can cause separation of the steeringshaft assembly, resulting in complete loss of steering, without prior warningand, possibly, an accident.
- Campaign:
- 81V088000 on 07/13/1981
- Component:
- Service brakes, air:controls:hand control
- Manufactured:
- 06/30/1979 - 12/31/1979
- Affected:
- 10,000
- Defect:
- The retaining pin for the brake control knob has been misaligned (off the center line of the valve plunger hole). this causes the knob to be overstressed at the retaining pin hole area causing it to separate from the valve.
- Correction:
- The holes will be retooled to provide correct alignment and plastic knobs will be replaced by knobs of stronger material having metal reinforcements.
- Notes:
- Vehicle description: trucks equipped with brake control knobs.system: service brakes; knob retaining pin.consequences of defect: with the knob broken off, the control valve wouldbecome difficult or impossible to operate. one or a combination of brakeapplications would not be possible and the vehicle could be parked in an unsafecondition. an accident and personal injury could result.
- Campaign:
- 81V153000 on 01/07/1982
- Component:
- Exterior lighting
- Manufactured:
- 09/30/1977 - 04/30/1981
- Affected:
- 209
- Defect:
- The right hand clearance lamp is obscured, from certain angles of vision, by the in-line precleaner air cleaner cap. the involved vehicles fail to conform to federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment".
- Correction:
- Dealer will replace the air cleaner with one of acceptable height.
- Notes:
- Vehicle description: trucks.system: lighting and communications; clearance lamp.consequences of defect: if the clearance lamp is not adequately visible, avehicle accident could occur.
- Campaign:
- 84V036000 on 04/10/1984
- Component:
- Suspension:rear:springs:leaf spring assembly
- Manufactured:
- 09/30/1978 - 04/30/1982
- Affected:
- 3,421
- Defect:
- Spring seat can deform, which causes a decrease in the clamping force in the suspension assembly. loss of clamping force may bring about axle misalignment or axle housing failure.
- Correction:
- The axle housing will be inspected and replaced, if necessary. the spring seats will also be replaced.
- Notes:
- Vehicle description: heavy trucks.system: suspension; rear spring seat.consequences of defect: loss of vehicle control could occur without warning,possibly resulting in an accident.
Home | Privacy