1979 FORD E150 Recalls (5)
- Campaign:
- 78V214000 on 10/11/1979
- Component:
- Seat belts:rear
- Manufactured:
- 07/31/1978 - 08/31/1978
- Affected:
- 874
- Defect:
- On the involved vehicles, the potential exists for the outboard seat belts to become trapped in the seat-bed pivoting mechanism. should the belt become trapped in the mechanism when the seat is converted to a bed, the belt may become cut or frayed.
- Correction:
- The dealer will install seat belt shields on the folding seat/bed pivoting mechanism and replace the outboard seat belt assemblies if damaged, free of charge.
- Notes:
- Vehicle description: trucks equipped with optional seat-beds.system: interior; seat bed seat belt (shoulder).consequences of defect: in the event of sudden braking or vehicle collision,the seat belt may not properly restrain the seat occupant and the risk ofpersonal injury is increased.
- Campaign:
- 79V117000 on 10/11/1979
- Component:
- Service brakes, hydraulic:pedals and linkages
- Manufactured:
- 01/31/1979 - 02/28/1979
- Affected:
- 82,000
- Defect:
- The involved vehicles were produced with brake push-rod to brake pedal retaining pins which were not heat-treated as specified. this could allow the brake pedal to become disengaged from the push-rod.
- Correction:
- Dealer will replace the suspect brake retaining pin.
- Notes:
- Vehicle description: passenger vehicles.system: service brakes; hydraulic linkage, pedal.consequences of defect: disengagement of the brake pedal would result in totalloss of service brakes, which could lead to loss of vehicle control and anaccident.note: the parking brake will remain operational even if service brakes arelost.
- Campaign:
- 79V153000 on 10/11/1979
- Component:
- Structure: frame and members:underbody shields
- Manufactured:
- 08/31/1978 - 12/31/1978
- Affected:
- 12,000
- Defect:
- Certain vehicles may not contain the specified body mounted heat shields. this could cause high floor pan temperatures when the engine is idled for extended periods of time. fouled spark plugs or other engine conditions could further increase exhaust temperatures.
- Correction:
- The dealer will install the necessary frame mounted heat shield, if missing.
- Notes:
- Vehicle description: trucks equipped with 300 and 460 cid engines.system: exhaust; body mounted heat shields.consequences of defect: these high temperatures could cause the rear floorcoverings to smoulder, resulting in smoke damage and personal injury.
- Campaign:
- 79V185000 on 10/11/1979
- Component:
- Wheels
- Manufactured:
- 08/31/1978 - 09/30/1978
- Affected:
- 22,500
- Defect:
- The wheel assembly may contain substandard welds in the area where the disc is attached to the rim. as a result, cracks can form in the wheel assembly, causing air loss and an underinflated tire.
- Correction:
- Dealer will inspect and replace any defective wheels without charge to owner.
- Notes:
- Vehicle description: light trucks equipped with 15 x 5.5k wheel assemblies.system: wheels; wheel assembly.consequences of defect: low tire inflation pressures could cause loss ofvehicle control and an accident. also, if the spot welds fail, the rim and tirecould separate from the wheel disc, with consequent loss of control andaccident.
- Campaign:
- 90V137000 on 07/31/1990
- Component:
- Seat belts:front:anchorage
- Manufactured:
- 08/31/1978 - 11/30/1984
- Affected:
- 13,637
- Consequence:
- Occupants would not be adequately protected in event ofan accident or sudden stop.
- Correction:
- Install proper mounting hardware and seat belts.
- Notes:
- Note: this recall was initialized by mark iii industries.system: seat belts, seat belt anchors, and seat mounting. dom: sept. 1978 tosept. 1984.description on defect: improper mounting hardware and improper safety restraintsystems may have been installed in these vehicles.
Home | Privacy