1977 MACK RL Recalls (8)
- Campaign:
- 79V133000 on 10/11/1979
- Component:
- Engine and engine cooling:engine
- Manufactured:
- 01/31/1977 - 02/28/1979
- Affected:
- 23,000
- Defect:
- In the event of turbocharger compressor wheel failure, one or more of the four capscrews that hold the turbocharger together may be struck by parts of the compressor wheel, resulting in the capscrews being damaged. if these capscrews are damaged to the point that they allow the compressor back plate to dislocate from the turbocharger bearing housing, engine lubricating oil may be allowed to escape under pressure, contacting the engine exhaust manifold sections or turbocharger turbine housing.
- Correction:
- Dealer will install a shield for the heads of the four capscrews, along with stronger sae 8 grade 8 capscrews, if necessary, at no cost to owner.
- Notes:
- Vehicle description: trucks equipped with endt (b) 676, etaz (b) 673a, and etay(b) 673a engines.system: engine and engine cooling.consequences of defect: engine lubricating oil, in the presence of a source ofignition, could lead to an engine compartment fire and serious injury tovehicle passengers.
- Campaign:
- 79V134000 on 10/11/1979
- Component:
- Steering:wheel and handle bar
- Manufactured:
- 05/31/1974 - 02/28/1978
- Affected:
- 64,150
- Defect:
- In the involved trucks it is possible the adjustable steering column rear mounting bracket could fail, allowing steering wheel assembly to fall down onto the operator"s lap.
- Correction:
- Dealer will install an additional bracket in this area to prevent the steering wheel from dislocating in the event of a bracket failure.
- Notes:
- Vehicle description: trucks.system: steering assembly; steering wheel and column.consequences of defect: while steering would remain functional in thiscondition, the element of surprise to operator could cause loss of vehiclecontrol and an accident.
- Campaign:
- 78V210000 on 10/11/1979
- Component:
- Service brakes, air:antilock:interconnecting assembly(wiring)
- Manufactured:
- 09/30/1977 - 08/31/1978
- Affected:
- 19,370
- Defect:
- Delays of up to about 2 seconds may exist in the brake application times to the brakes on the bogie axles in the presence of certain types of wheel speed sensor signal discontinuities or distortions that may occur as a result of sensor wire failure. this constitutes a non-compliance to federal motor vehicle safety standard no. 121, "air brake systems".
- Correction:
- Dealer will install new wheel speed sensors that incorporate improved wiring and the present bogie anti-wheel lock system will be changed to an axle-to-axle system for improved reliability.
- Notes:
- Vehicle description: heavy trucks.system: service brakes; electrical wiring and connectors.consequences of defect: this delay in effective braking action could lead to anaccident under certain traffic conditions.
- Campaign:
- 77V149000 on 10/11/1979
- Component:
- Wheels:multi piece
- Affected:
- 250
- Defect:
- The front wheel aluminum hubs on the involved vehicles may be subject to cracks which may progress circumferentially around the barrel of the hub. this could lead to a fracture in the "barrel" position of the hub and complete hub failure.
- Correction:
- Dealer will install steel hubs in place of aluminum hubs without charge to owner.
- Notes:
- Vehicle description: trucks equipped with ff-931 front axles.system: wheels; aluminum hubs, front.consequences of defect: hub failure could result in loss of vehicle control andan accident.note: hub failure may be indicated by an audible sound at the instant of hubseparation, along with thumping or wheel wobble. hub may separate from thewheel and still be retained on the axle.
- Campaign:
- 78V030000 on 10/11/1979
- Component:
- Service brakes, air:supply:hoses, lines/piping, and fittings
- Manufactured:
- 11/30/1975 - 12/31/1977
- Affected:
- 400
- Defect:
- A design deficiency exists in the air dryer piping in the area of the pressure relief valve and compressor governor control link. moisture is passed and builds up in this relief valve and control line. in freezing ambient temperatures, this moisture may freeze, allowing the chassis air system pressure to exceed 150 psi. excessive air system pressure can cause separation of air piping connections and air system valve failure.
- Correction:
- The dealer will relocate the air system compressor governor line and pressure relief valve to eliminate moisture accumulation.
- Notes:
- Vehicle description: trucks equipped with anchorlok air dryers.system: service brakes; air system and governor control line (air dryer).consequences of defect: when this occurs, automatic application of the chassisemergency spring brakes and trailer brakes could cause loss of vehicle controlwithout prior warning and a vehicle accident.note: owner/driver is advised not to operate vehicle if air pressure exceeds15o psi.
- Campaign:
- 77V173000 on 10/11/1979
- Component:
- Engine and engine cooling:cooling system:fan
- Affected:
- 48,000
- Defect:
- The flex blade fans on the involved vehicles may develop cracks in the laminated stiffener as a result of fatigue during operation. if such a condition exists and the cracks go undetected, continued operation could cause pieces of the stiffener to break off.
- Correction:
- Dealer will replace the original fan with a steel fixed blade fan, free of charge.
- Notes:
- Vehicle description: trucks equipped with six-cylinder engines.system: engine cooling; fan.consequences of defect: broken pieces can be propelled outside of the fanshroud and will present an immediate danger and possible injury to personsstanding nearby.note: prior to correction, vehicle should not be serviced with the hood raisedand the engine running.
- Campaign:
- 77V205000 on 10/11/1979
- Component:
- Suspension:rear:springs:leaf spring assembly:hanger/bracket
- Manufactured:
- 04/30/1977 - 09/30/1977
- Affected:
- 7,400
- Defect:
- A deficiency exists in the welds securing the rear spring insulator bracket to the axle housing. this is due to improper positioning of the weld, in relationship to the bracket and axle housing. failure of the welds would cause separation of the spring insulator bracket and the axle housing, resulting in improper alignment of the affected axle.
- Correction:
- Dealer will reweld the insulator spring bracket at no cost to owner.
- Notes:
- Vehicle description: heavy trucks.system: suspension; tandem axle.consequences of defect: this condition could cause a loss of vehicle controland a vehicle accident.
- Campaign:
- 78V222000 on 10/11/1979
- Component:
- Electrical system:wiring
- Manufactured:
- 06/30/1977 - 08/31/1978
- Affected:
- 161
- Defect:
- A short circuit could occur due to chafing or wire disconnection in the box.
- Correction:
- The wiring in the sleeper box will be corrected, free of charge.
- Notes:
- Vehicle description: heavy truck tractors equipped with the able body company"ssleeper box.consequences of defect: a short circuit creates a potential fire hazard whichcould jeopardize the safety of vehicle occupants.
Home | Privacy